GE Spacemaker PDW1800N Install Manual

Also see for PDW1800NBB - Profile 18-in Dishwasher: Owner's manual Energy guide Dimensions and installation information

Contents

GE Spacemaker PDW1800N Install Manual Manual pdf 13 page image

11Installation InstructionsSTEP 14 CONNECT POWER SUPPLYSkip this step if equipped with power cord.Verify that power is turned off at the source.• Remove junction box cover “A”.• Locate the three dishwasher wires, (white, black and green)with stripped ends. Insert dishwasher wires through the smallhole in the junction box “B”.• Secure house wiring to the bottom of the junction box with astrain relief “C”.• Use wire nuts to connect incoming ground to green, white towhite and black to black “D”.• Replace junction box cover “E”. Check to be sure that wiresare not pinched under the cover.STEP 15 PRETEST CHECK LISTReview this list after installing your dishwasher to avoidcharges for a service call that is not covered by yourwarranty.■ Check to be sure power is OFF.Check to be sure power is OFF.■ Open door and remove all foam and paper packaging.Open door and remove all foam and paper packaging.■ Locate the Owner’s Manual in the literature package.Locate the Owner’s Manual in the literature package.■ Read the Owner’s Manual for operating instructions.Read the Owner’s Manual for operating instructions.■ Check door opening and closing. If door does not open andCheck door opening and closing. If door does not open andclose freely or tends to fall, check spring adjustments. SeeStep 1.■ Check to be sure that wiring is secure under the dishwasher,Check to be sure that wiring is secure under the dishwasher,not pinched or in contact with door springs or othercomponents. See Step 9.■ Check door alignment with tub. If door hits tub, levelCheck door alignment with tub. If door hits tub, leveldishwasher. See Step 10.■ Pull lower rack out, about half way. Check to be sure it doesPull lower rack out, about half way. Check to be sure it doesnot roll back or forward on the door. If the rack moves,adjust leveling legs. See Step 10.■ Check door alignment with cabinet. If door hits cabinet,Check door alignment with cabinet. If door hits cabinet,reposition or relevel dishwasher. See Step 10.■ Verify water supply and drain lines are not kinked or inVerify water supply and drain lines are not kinked or incontact with other components. Contact with motor ordishwasher frame could cause noise. See Step 8.■ Turn on the sink hot water faucet and verify waterTurn on the sink hot water faucet and verify watertemperature. Incoming water temperature mustbe between 120°F and 150°F. A minimum of 120°Ftemperature is required for best wash performance. See“Prepare Hot Water Line,” page 5.■ Add 2 quarts of water to the bottom of the dishwasher toAdd 2 quarts of water to the bottom of the dishwasher tolubricate the pump seal.■ Turn on water supply. Check for leaks. Tighten connectionsTurn on water supply. Check for leaks. Tighten connectionsif needed.■ Remove protective film if present from the control panelRemove protective film if present from the control paneland door.■ Avoid service call charges by ensuring there is an air gapAvoid service call charges by ensuring there is an air gapor drain hose routed through the required 32" minimumheight.Figure GG#282 FrenchIf house wiring is not 2-wire with ground, aground must be provided by the installer.When house wiring is aluminum, be sure touse UL Listed anti-oxidant compound andaluminum-to-copper connectorsWARNING11WhiteGround BlackCheck That White, Black andGreen Dishwasher Wires Are ThreadedThru Hole in BackRemoveJunction BoxCoverInsert PowerCord Wires ThruStrain Reliefand TightenUse UL ListedWire NutsACBD

/ 14

Related manuals for GE PDW1800NBB - Profile 18-in Dishwasher