IHP CAPELLA 33 Installation And Operation Instructions Manual

Also see for CAPELLA 33: Installation and operation instructions

Contents

IHP CAPELLA 33 Installation And Operation Instructions Manual Manual pdf 3 page image

WARNINGDo not install or operate this fireplacethrough a switch wired in the 120 VAC or240 VAC circuits. The only approved wiringfor a switch is through the low voltagecircuit (24 VAC) as shown on Page 15.NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 3900974-00NC 06/2019CONGRATULATIONS!In selecting this Innovative Hearth Products (IHP) electric fireplace, you have chosenthe finest and most dependable fireplace found anywhere. A beautiful and prestigiousaddition to the finest homes.Please read and carefully follow all of the instructions found in this manual. Pleasepay special attention to the safety instructions provided in this manual. The instruc-tions included here will assure that you have many years of dependable and enjoyableservice from your product.TABLE OF CONTENTSImportant Safety Information ............Page 2Packaging List...................................Page 3Introduction ......................................Page 3General Information ..........................Page 3Locating Fireplace .............................Page 3Tools/Supplies Required .................. Page 3Framing Specifications ..................... Page 4Fireplace Specifications.................... Page 4Clearances ....................................... Page 6Pre-installation ................................. Page 6Installation Steps ............................. Page 6Electrical Connections ...................... Page 7Final Finishing .................................. Page 7Break-In Period ................................ Page 7Control Panel Operation ................... Page 7Remote Control Operation ............... Page 8Maintenance..................................... Page 9Wiring Diagrams .............................. Page 11Troubleshooting ............................... Page 16Replacement Parts ........................... Page 17Optional Accessories........................ Page 19Warranty Certificate.......................... Page 21Please read and understand theseinstructions before installing, operating,or servicing this product.INTRODUCTIONThis Electric Fireplace is designed forresidential applications to be framed in asa zero clearance fireplace.This appliance has been tested in accor-dance with UL 2021 and CSA C22.2 No.46-M198 standards for fixed and locationdedicated electric room heaters.Installation must conform to local codes.In the absence of local codes, electricalwiring and grounding must comply withthe National Electrical Code ANSI/ NFPA70 - latest edition. In Canada, the currentCSA C22-1 Canadian Electrical Code - latestedition.GENERAL INFORMATIONPower Supply Wire Specifications120 Volt, 60 Hz, 1500 Watts:(ref. Page 11)Hard Wire Connection - Use two conductor,non-metallic sheath cable with ground wire(total three wires) for the incoming powersupply. The wire used must conform to localand national electrical codes for the specifiedpower consumption rating. See Table 1.240 Volt, 60 Hz, 3000 Watt:(ref. Page 12)Use three conductor, non-metallic sheath cablewith ground wire (total four wires) for theincoming power supply. The wire used mustconform to local and national electrical codesfor the specified power consumption rating.See Table 1.Figure 1LOCATING YOUR IHP ELECTRICFIREPLACEYour new fireplace may be installed into exist-ing framing or built into a wall (see Figure 1).When choosing a location for your new fireplace,ensure that the general instructions are followed.Also, for the best effect, install the fireplaceout of direct sunlight and away from overheadlighting. See Figure 1.fireplace shown in gray.TOOLS AND BUILDING SUPPLIESNORMALLY REQUIREDTOOLS:Phillips Screwdriver7/16" Socket DriveHammerSaw And/or Saber SawLevelMeasuring TapePlumb LineElectric Drill And BitsPliersSquareGlovesIMPORTANT NOTE: This fireplace systemis not difficult to install. However, in theinterest of safety, it is recommended that theinstaller be a qualified or certified “trades-man” familiar with commonly acceptedfireplace installation and safety techniquesas well as prevailing local codes.BUILDING SUPPLIES:Framing MaterialsWall Finishing MaterialsCaulking Materials(noncombustible)Top View Showing ApprovedRoom Locations of FireplacePACKAGING LISTThis assembled Electric Room Heater is pack-aged with:• One accessory package located in thefirebox, containing;1. One Installation and Operation Manual.2. One Remote Control.Wall Thermostat Wire GageVoltage Wire Gage5 VOLTS 18 GAGEPower Supply Wire GageVoltage Wire Gage Fuse120 V 14 GA. 15 AMP240 V 14 GA. 20 AMPTable 1Wall Thermostat Kit(optional kits, see Page 19)Low voltage wire is provided for the wall switchconnection. The wires gage requirements areshown on Table 1.