IHP CAPELLA 33 Installation And Operation Instructions Manual

Also see for CAPELLA 33: Installation and operation instructions

Contents

IHP CAPELLA 33 Installation And Operation Instructions Manual Manual pdf 8 page image

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.8REMOTE CONTROL OPERATION:Figure 5 - Remote ControlOPERATION:1. Plug in the power plug, turn on the powerswitch, you can hear the buzzer "beep" once,that means the power is connected. Press the“ ”key: flame and ember bed LED lightsare in the brightest level, the flame colorsblue and yellow, ember bed is red, ceilinglight is orange, the heating system is in OFFstatus; then click “ ” again, the fireplaceis turned OFF; the other keys will only workif the “ ” is turned back ON;NOTE: If power is not in OFF condition, shut-down by the remote control, then next time turnON by the remote control, the existing settingwill resume to the previous shutdown setting.If lighting is off before the power is turned off,press this key again, the flame, ember bed andceiling light are in the brightness level. Theheater is OFF.2. Blue key ( ) to control the brightness ofblue flame LED, (3) different brightnesslevels, multiple times to cycle through the(3)brightness levels and OFF;3. Yellow key ( ) to control the brightness ofyellow flame LED, (3) different brightnesslevels, multiple times to cycle through the(3) brightness levels and OFF;4. Flame key ( ) to control ON/OFF of all theflames, ember and mood lighting; next timeturn on by the flame key, the existing settingwill resume to the previous turn off setting.5. EMBER key ( ), to control the brightnessof the ember LED (3) different brightnesslevels, multiple times to cycle through the(3) brightness levels and OFF;6. MOOD key / Ceiling Light ( ), to controlthe brightness of the mood LED (3) differentbrightness levels, multiple times to cyclethrough the (3) brightness levels and OFF;Remote Control Function(with LED display on firebox)Power ON/OFF750W1500WHeater ON/OFFHeater lockand unlockOne button preset/resetto defaultIndividual flame button:blue and yellow on leftand right. No symbol ortop and bottomFlame Button ON/OFFMood Key / Ceiling LightEmber Bed LightTemperature ControlComfort Setting at77° F (25° C)CAUTION• Do Not Use Old Batteries WithNew Ones.• Do Not Use Batteries OtherThat The Type Specified (2ea. AA).• Ensure Batteries Are CorrectlyInstalled In Remote Control.7. Heater ON/OFF key ( ): press first, theheater is ON the heater is working on ”HIGH”temperature status, two groups of heatingsystem turn ON at 1500W; press again,theheater is OFF;8. Press HIGH key ( ): two groups ofheating system is working at 1500W, theindictor is in red color;9. Press LOW key ( ): one group of heatingsystem is working at 750W, the indictor isin blue color;10.Press TEMP key ( ): the indictor is a purplecolor, the fireplace is auto setting the roomtemperature at 77° F (25° C), When room tem-perature exceed 77° F (25° C), the heater(s)will turn off and stop working,and when roomtemperature drops below 72° F (22° C), theheater(s) will turn on automatically again.NOTE: “HIGH” “LOW” “TEMP” key works whenthe “ ”“Heater On/off” key is in ON posi-tion. When temperature sensor detected thetemperature greater than 113° F (45° C), theheater will automatically turns off.Press and hold "heater on/off" key for 5seconds to lock heater and related keys.Press and hold "heater on/off" key for 5seconds to unlock heater and related keys.NOTE: Lighting functions will still operatewhile heater is locked.11. Key is “One button LED light recovery”,preset and reset the flame and other lightingeffect. User preset the flame and lightingcondition, when user preset to their desireflame combination, press for 3 seconds(hear beep sound), store the current status.After user changed the flame setting severaltimes and return to preset condition. Usercan press “one button recovery” back topreset condition. If user would like to presetanother set of lighting effect, after that, press3 seconds and will store the latest setting.900974-00NC 06/2019