558SET MODE78 Set mode programmingSet mode is used to change the conditions of the transceiver’sfunctions: Scan type, Scan resume timer, Dual/Tri-watch, Beeptone, LCD contrast, Automatic foghorn frequency, Radio power,Scrambler type* and Scrambler code.**Appears only when the optional scrambler unit is installed.Available functions may differ depending on how they areset by the dealer.q Turn power OFF.w While pushing and holding [16•C], turn power ON to enterSet mode.e After the display appears, release [16•C].r Rotate [CHANNEL] to select the desired item, push[CHANNEL•ENTER].t Rotate [CHANNEL] to select the desired condition of theitem.y Push [CLR], or rotate [CHANNEL] to select “EExxiitt,” thenpush [CHANNEL•ENTER] to exit set mode and returns tonormal operation condition. Set mode itemsD Scan typeThe transceiver has 2 scan types: Normal scan and Priorityscan. Normal scan searches all TAG channels in the selectedchannel group. Priority scan searches all TAG channels in se-quence while monitoring Channel 16.DD Scan resume timerThe scan resume timer can be selected as a pause (OFF) ortimer scan (ON). When OFF is selected, the scan pausesuntil the signal disappears. When ON is selected, the scanpauses 5 sec. and resumes even if a signal has been re-ceived on any other channel than Channel 16.--Set Mode--Scan TimerON˘OFF<ENT˘OK>Default: OFF--Set Mode--Scan Type˘PriorityNormal<ENT˘OK>Default: PriorityRotate--Set Mode--˘Scan TypeScan TimerDual/TriBeepContrastFoghorn FrequencyRadio PowerScrambler TypeScrambler CodeExit• SET MODE CONSTRUCTION

explicit definitions

in case of emergency

operating rules

panel description

i function display

basic operation

i receiving and transmitting

i call channel programming

i channel comments

i optional voice scrambler operation

scan operation

i setting tag channels

I Operation

dsc operation

i mmsi code check

i dsc address id

d deleting individual id

d programming group id

d deleting group id

i position and time programming

i position and time indication

i distress call

i transmitting dsc calls

d transmitting a group call

d transmitting an all ships call

d transmitting a position request call

i receiving dsc calls

d receiving an individual call

d receiving a position request call

d receiving a polling request call

i received messages

d other messages

dsc set mode

other functions

i rx speaker function

i hailer operation

set mode

connections and maintenance

i supplied accessories

i mounting the transceiver

I MB-75 installation

troubleshooting

specifications and options

I Options

channel list

Icom iC-M505 Instruction Manual

explicit defenitions

OPERATING RULES

PANEL DESCRIPTION

Function display

Microphone

BASIC OPERATION

Receiving and transmitting

Call channel programming

Channel comments

Optional voice scrambler operation

SCAN OPERATION

Setting TAG channels

DUALWATCH/TRI-WATCH

DSC OPERATION

MMSI code check

DSC address ID

Position and time programming

Position and time indication

Distress call

d regular call

transmitting dsc calls

Receiving DSC calls

Received messages

DSC Set mode

Intercom operation

RX Speaker function

Hailer operation

Set mode programming

lcd contrast

Connections

Antenna

Mounting the transceiver

MB-75 installation

UT-112/UT-98 installation

Specifications

Options

CHANNEL LIST

TEMPLATE

IC-M505

A. Introduction

D. Dynamic information

G. Display

B. Activation of the AIS

D. Explanation of basic operation

E. Advanced operation (*)

function display

receiving and transmitting

Call channel programmng

Functon dsplay

Operaton

position and time programming

Poston and tme ndcaton

Dstress call

receiving dsc calls

received messages

Intercom operaton

Recevng DSC calls

Haler operaton

Connectons

mounting the transceiver

Mountng the transcever

Optons