6711SPECIFICATIONS AND OPTIONS1011 SpecificationsDD General• Frequency coverage : Tx 156.000–161.450 MHzRx 156.000–163.425 MHz• Mode : FM (16K0G3E), DSC (16K0G2B)• Channel spacing : 25 kHz• Current drain (at 13.8 V) : TX high 5.5 A max.Max. audio 1.5 A max.• Power supply requirement : 13.8 V DC (10.8 to 15.6 V)(negative ground)• Frequency stability : ±10 ppm• Operating temp. range : –20°C to +60°C• Antenna impedance : 50 Ω nominal• Dimensions : 165(W) × 110(H) × 123.2(D) mm(Projections not included)• Weight : Approx. 1450 gDD Transmitter• Output power : 25 W/1 W• Modulation system : Variable reactance frequencymodulation• Max. frequency deviation : ±5.0 kHz• Spurious emissions : Less than 0.25 μW• Microphone impedance : 2 kΩ• Frequency error : Less than ±1.5 kHz• Adjacent channel power : More than 70 dB• Audio harmonic distortion : Less than 10 %• Residual modulation : More than 40 dB• Audio frequency response : +1dB to –3dB of 6 dB oct. from300 Hz to 3000 HzDD Receiver• Receive system : Double conversionsuperheterodyne• Sensitivity (20 dB SINAD) : –5 dBμ emf (typical)• Squelch sensitivity : Less than 1 μV• Intermodulation rejection ratio : More than 73 dB• Spurious response rejection ratio : More than 73 dB• Adjacent channel selectivity : More than 73 dB• Audio output power : More than 2 W at 10% distortionwith a 4 Ω load• Hum and noise : More than 40 dB• Audio frequency response : +1dB to –3dB of –6 dB oct. from300 Hz to 3000 HzAll stated specifications are subject to change without notice orobligation.

explicit definitions

in case of emergency

operating rules

panel description

i function display

basic operation

i receiving and transmitting

i call channel programming

i channel comments

i optional voice scrambler operation

scan operation

i setting tag channels

I Operation

dsc operation

i mmsi code check

i dsc address id

d deleting individual id

d programming group id

d deleting group id

i position and time programming

i position and time indication

i distress call

i transmitting dsc calls

d transmitting a group call

d transmitting an all ships call

d transmitting a position request call

i receiving dsc calls

d receiving an individual call

d receiving a position request call

d receiving a polling request call

i received messages

d other messages

dsc set mode

other functions

i rx speaker function

i hailer operation

set mode

connections and maintenance

i supplied accessories

i mounting the transceiver

I MB-75 installation

troubleshooting

specifications and options

I Options

channel list

Icom iC-M505 Instruction Manual

explicit defenitions

OPERATING RULES

PANEL DESCRIPTION

Function display

Microphone

BASIC OPERATION

Receiving and transmitting

Call channel programming

Channel comments

Optional voice scrambler operation

SCAN OPERATION

Setting TAG channels

DUALWATCH/TRI-WATCH

DSC OPERATION

MMSI code check

DSC address ID

Position and time programming

Position and time indication

Distress call

d regular call

transmitting dsc calls

Receiving DSC calls

Received messages

DSC Set mode

Intercom operation

RX Speaker function

Hailer operation

Set mode programming

lcd contrast

Connections

Antenna

Mounting the transceiver

MB-75 installation

UT-112/UT-98 installation

Specifications

Options

CHANNEL LIST

TEMPLATE

IC-M505

A. Introduction

D. Dynamic information

G. Display

B. Activation of the AIS

D. Explanation of basic operation

E. Advanced operation (*)

function display

receiving and transmitting

Call channel programmng

Functon dsplay

Operaton

position and time programming

Poston and tme ndcaton

Dstress call

receiving dsc calls

received messages

Intercom operaton

Recevng DSC calls

Haler operaton

Connectons

mounting the transceiver

Mountng the transcever

Optons