JCM Taiko Series Operation And Maintenance Manual

Contents

JCM Taiko Series Operation And Maintenance Manual Manual pdf 24 page image

P/N 960-100175R_Rev. 6 {EDP #200824} © 2016, JAPAN CASH MACHINE CO., LTD.2 - 4Section 2 Taiko™ Series Banknote Acceptor InstallationTable 2-3 lists the various special DIP Switchsettings available for programing the Taiko™ Unit.Denomination Setting ModePerform the Accept/Inhibit setting function for theBanknote Denomination required based on theSoftware requirements of the Specific Country inwhich it is being used. The default settings are toaccept all Denominations of the Specific Country.ACCEPT SETTING MODETo establish an “Accept” setting function, performthe following steps:1. Remove power from the Taiko™ Unit.2. Set DIP Switch No.1 and No.6 to ON (See Figure2-12 above).3. Re-apply Power to the Taiko™ Unit.4. After the Front Panel LED display flashes White,set DIP Switch No.1 to the OFF position to enterthe Setting Mode.5. Insert the Banknote Denomination to be acceptedinto the Insertion Slot. The setting registered iscorrect if the Front Panel LED Display flashes alight Blue Color, and the inserted Banknote isreturned.6. Insert the next Banknote Denomination to beaccepted until all required values have beenprocessed, set and accepted.INHIBIT SETTING MODETo establish an “Inhibit” setting function, performthe following steps:1. Remove Power from the Taiko™ Unit.2. Set DIP Switch No.1, No. 6 and No.7 to ON (Fig-ure 2-13).3. Re-apply Power to the Taiko™ Unit.4. After the Front Panel LED display flashes White,set DIP Switch No.1 to the OFF position to enterthe Setting Mode.5. Insert the Banknote Denomination to be inhibitedinto the Insertion Slot. The setting is registered ifthe Front Panel LED display flashes an OrangeColor, and the inserted Banknote is returned.6. Insert next Banknote Denomination to be inhib-ited until all required values have been processed.The Banknote ‘Accept’ or ‘Inhibit’ programingoperations are now complete.LED Pattern Setting ModeThe LED Color Pattern Type can be changedaccording to user preference. Select between Pat-tern 1 or Pattern 2, the default setting is Pattern 1.DEFINING PATTERN 1To define a “Pattern 1” (a flashing Color Sequence)operating function, perform the following steps:1. Remove Power from the Taiko™ Unit.2. Set DIP Switch No.1, No.2 and No.7 to ON (Fig-ure 2-14).3. Re-apply Power to the Taiko™ Unit.4. Set DIP Switch No.1 to OFF to cause the LEDDisplay Pattern to emulate “Pattern 1” whenoperating.Table 2-3 Programming DIP Switch SettingsSetting Function SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8Denom.ValueSettingModeAcceptSetting ON OFF OFF OFF OFF ON OFF OFFInhibitSetting ON OFF OFF OFF OFF ON ON OFFLEDPatternSettingModeDefinePattern 1 ON ON OFF OFF OFF OFF ON OFFDefinePattern 2 ON OFF ON OFF OFF OFF ON OFFEncryption CodeInitialization SettingModeON ON ON ON ON ON OFF OFFDownload Mode**. For details concerning Taiko™ Software Download and AdjustmentModes, refer to “Software Downloading Procedure” on page 6-1 inSection 6 of this Service Manual.ON OFF OFF OFF OFF OFF ON ONAdjustment Mode* ON ON OFF OFF OFF OFF OFF ONONFigure 2-12 “Accept” Mode DIP SwitchSettingsFigure 2-12 “Accept” Mode DIP Switch SettingsONFigure 2-13 “Inhibit” Mode DIP SwitchSettingsFigure 2-13 “Inhibit” Mode DIP Switch SettingsONNOTE: The Accept/Reject setting for a Banknotedenomination can be confirmed by observing theFront Panel LED Color. After an initial operationis performed, the LED will flash a number oftimes equal to the total number of Banknotedenominations processed. Blue indicates an‘Accept’ setting and Red indicates a ‘Reject’setting.Figure 2-14 Define Pattern 1 DIP SwitchSettingsFigure 2-14 Define Pattern 1 DIP Switch SettingsON