JCM Taiko Series Operation And Maintenance Manual

Contents

JCM Taiko Series Operation And Maintenance Manual Manual pdf 25 page image

P/N 960-100175R_Rev. 6 {EDP #200824} © 2016, JAPAN CASH MACHINE CO., LTD.2 - 5Installation Taiko™ Series Banknote Acceptor Section 2DEFINING PATTERN 2To define a “Pattern 2” (a fading Color Sequence)operating function, perform the following steps:1. Remove Power from the Taiko™ Unit.2. Set DIP Switch No.1, No.3 and No.7 to ON (Fig-ure 2-15).3. Re-apply power to the Taiko™ Unit.4. Set DIP Switch No.1 to OFF to cause the LEDDisplay Pattern to emulate “Pattern 2” whenoperating.Encryption Code Initialization SettingModeWhen the ccTalk Encrypted Communication Codeis unknown, use the set the Encryption Code Initial-ization DIP Switch setting to use the last 6 digits ofthe specific Taiko™ Serial Number, located on theback side of a Taiko™ Unit as the EncryptionCode.To set the “Encryption Mode” operating function,perform the following steps:1. Remove Power from the Taiko™ Unit.2. Set DIP Switch No.1 through No.6 to ON, andSwitches No.7 and No.8 to OFF (Figure 2-16).3. Re-apply Power to the Taiko™ Unit.4. Set DIP Switch No.1 to OFF to initialize theEncryption Code setting.The Taiko™ installation DIP Switch settings arenow complete.Error Codes & ConditionsTable 2-4 lists the Red Error Code flash sequencedefinitions displayed by the Taiko™ Front PanelLED indicator.Interface Connector PinAssignmentsTable 2-5, Table 2-6, Table 2-7 and Table 2-8 listthe various Connector Pin Labels for adapting theseavailable Communication Standards to the Unit.Table 2-4 Red LED Error Code Flash DefinitionsRed Flashes Error Indicated2 ROM Error3 Banknote Jam inside Ejection Slot4 Banknote remains inside the Transport Path5 EEPROM Read/Write Error6 Motor Error8 Entrance Solenoid Error9 Exit Solenoid Error12 Sensor Operation with Abnormal TimingFigure 2-15 Define Pattern 2 DIP SwitchSettingsFigure 2-15 Define Pattern 2 DIP Switch SettingsONFigure 2-16 Encryption Mode DIP SwitchSettingsFigure 2-16 Encryption Mode DIP Switch SettingsONTable 2-5 Serial ID-003/MDB Interface PinAssignmentsPin No. SignalName I/O **. I/O (Input/Output) is the function viewed from the Banknote AcceptorSide.Function1 NC - No Connection2 NC - No Connection3 RXD- IN Data Receive Line(Active when current is present)4 RXD+5 TXD- OUT Data Send Line(Active when current is present)6 TXD+7 Vcc - +12V DC Power (7-Pin)8 Vss - Power Ground9 Vcc - +24V DC Power (9-Pin) ††. 24V DC is available only when the optional 24V DC Specification isused.10 NC - No ConnectionTable 2-6 ccTalk Interface Pin AssignmentsPin No. SignalName I/O **. I/O (Input/Output) is the function viewed from the Banknote AcceptorSide.Function1 ccTalk IN/OUT ccTalk Send/Receive Line2 ccTalk - ccTalk GND Line3 NC - No Connection4 NC - No Connection5 NC - No Connection6 NC - No Connection7 Vcc - +12V DC Power (7-Pin)8 Vss - Power Ground9 Vcc - +24V DC Power (9-Pin) ††. 24V DC is available only when the optional 24V DC Specification isused.10 NC - No ConnectionTable 2-7 Pulse Interface Pin AssignmentsPin No. SignalName I/O * Function1 NC - No Connection2 NC - No Connection3 Enable/Disable (-) IN-Enable/Disable Signal Input Line(Enabled when current is present)(Disabled when current is NOT present)No Connection4 Enable/Disable (+)5 Vend (-) OUT Pulse Signal Output Line(Active when current is present)6 Vend (+)7 Vcc - +12V DC Power (7-Pin)Figure 2-17 ID-003/MDB/ccTalk/Pulse Inter-face ConnectorFigure 2-17 ID-003/MDB/ccTalk/PulseInterface ConnectorInternal 10-Pin S10B-PADSS-1 (JST)