Kenwood 5.1 KRF-V7050D Instruction Manual

Contents

Kenwood 5.1 KRF-V7050D Instruction Manual Manual pdf 31 page image

31OperationsThe remote control supplied with this receiver) is also capableof controlling components from a variety of manufacturers onceyou register the appropriate setup codes into the remote controlunit.Basic remote control operations for other componentsLow battery warningReplace all two batteries with new ones when you notice a shorteningof the distance from which the remote control will operate. The remotecontrol is designed to retain setup codes in memory while you changebatteries.(For VR-507)Registering setup codes for othercomponents (RC-R0720)1Find the setup code of the component to be registered.• Refer to the setup code lists to find the setup code for the componentto be registered. fiExample: To register a DVD made by KENWOOD, you would enter“0534”.2Press the source key (DVD, CBL, VCR, TV, DSS, CD,RECEIVER).3Press and hold the SET UP key until the LED blinks twice,then release the SET UP key.4Press the numeric key to enter the first four-digit code forthe component.• If performed correctly, the LED will blink twice.• Point the remote control at the component and press POWER keyonce. It should turn ON/OFF but if it does not repeat step 2 to 4.• If the component still does not work, try searching for the code.¤• If the component does not have a POWER key, press PLAY keyinstead.Input Component Maker Code Key(DVD) DVD player KENWOOD 0534 DVDProgramming TV/VCR combo controlPerform the following instructions to control a TV/VCR Combo:1Turn on the TV/VCR Combo and insert a video cassette.• Read steps 2 to 4 completely before proceeding. You may want tohighlight or write down the code for the component you wish toprogram before moving onto step 2.2Press the VCR key once. Next, press and hold the SET UPkey until the LED blinks twice, then release the SET UPkey.3Use the setup codes for TV/VCR Combos to locate thebrand name, then press the numeric key to enter the firstfour-digit code for your component. fl• If performed correctly, the LED will blink twice.• If the LED did not blink twice, repeat steps 2 through 3 and tryentering the same code again.4Point the remote control at the component and press thePOWER key once.• It should turn off. If it does not respond, repeat steps 2 through 3,trying each code for your component until you find one that works.• If it still does not work, try searching for the code, see “Searching foryour code”. ¤• If the device does not have a POWER key, press PLAY key instead.5If you have located a setup code that works, but it has aseparate TV code, you will also need to program it intothe remote control to access the volume control asfollows:1 Press the TV key once.• The LED will blink twice.2 Press the numeric key to enter the TV code for your TV/VCRcombo.• If the code is correct, the LED will blink twice.If there is no separate TV code listed, you will need toperform the following steps to access the volume control:1 Press and the hold SET UP key until the LED blinks twice,then release the SET UP key.2 Press the numeric key to enter “9 - 9 - 3” .• The LED will blink twice.3 Press the VCR key once.•The LED will blink twice.5Repeat steps 2to 4to register additional componentsuntil all components have been registered.Notes• Although each setup code is designed to work with a number ofdifferent models, certain codes may not work with some models.(Also, certain codes may only operate some of the functions availableon a given model.)• In case the code for TV/VCR combos does not work, enter the TVcode and the VCR code respectively after checking the codes (See“Searching for your code”).• For TV/VCR combos – if there is no separate TV code listed, enter thecode, enter “9-9-3,” and press VCR key instead.Numeric keysSourcekeysRC-R0720POWERLEDSET UP