Kenwood CT/KXF-W Instruction Manual

Also see for CT-203: Instruction manual Instruction manual Instruction manual Instruction manual Service manual

Kenwood CT/KXF-W Instruction Manual Manual pdf 16 page image

CT-2050/203/KXF-W6010/W4010 (En/M)16Each press of the MODE key changes the setting.1 “LEVEL” lights up: Recording level setting mode2 “BAL.” lights up: Recording balance setting mode3 “BIAS” lights up: Recording bias setting mode (Deck B of theCT-2050/KXF-W6010 only)4 “LEVEL”,“BAL.”,and “BIAS”go off: Counter display modeSet the recording level.÷ Adjust the recording level so that the 0 dB of the peak level indicatorssometimes lights up.÷ The recording level can be adjusted on both decks A and B. (CT-203/KXF-W4010; Deck B only)lights uplights upThe cassette deck incorporates the Dolby HX Pro headroomextension function and auto-bias function to provide a re-cording with superior high-frequency characteristics.Since this unit is not designed for recording with metal(TYPE ) tapes, do not use metal tapes for recording.How to record (CT-203/KXF-W4010; Deck B only)Preparation÷ Select by operating the input selector of the amplifier (optional).÷ In case of recording a FM broadcast,refer to discription of "How to usethe MPX FILTER key". &÷ While pressing the PAUSE (8) key, press the REC/ARM (¶) key.0dB.Recording level display.1Make “Playback (recording) preparation”.0(CT-203/KXF-W4010; Insert a tape in deckB.)2(Load a disc in the CD player.): Keys and control used in the operations described on this page.Normal recording1 Select the source to be recorded.32 Perform auto-bias adjustment. (The bias adjustment is applied to deck B.)AUTO BIAS÷ The optimum bias is set in about 40 seconds, after which the deckenters the stop mode.÷ For a fine adjustment after setting AUTO BIAS, refer to the descriptionof “Bias level adjustment”. (CT-2050/KXF-W6010 only) &÷ To cancel the auto-bias adjustment operation in the middle, press thestop (7) key.÷÷÷÷÷ Recording is possible even when the auto-bias setting is omitted.÷ If the amount of remaining tape is small, the auto-bias adjustment maybe canceled in the middle and tape stopped at that position.÷ The bias level is canceled when the eject (0) key is pressed.1Play a music source.2Enter the record-pause mode.8PAUSE ¶REC/ARM3Press the MODE key and select the "BAL."mode. MODE4Adjust the recording balance.REC LEVEL/BAL./BIAS∞MAX/R∞MIN/LRight sounddecreases.Left sounddecreases.5Press the MODE key and select the"LEVEL" mode.MODE6Adjust the recording level.REC LEVEL/BAL./BIAS∞MAX/R∞MIN/LRecordingleveldecreases.Recordinglevelincreases.7Stop playing the source.÷ In counter, adjust the recording balance level so that the left and rightdisplays are the same. You can also check with the Ò and Â peak levelindicators.Right channel levelLeft channel levelCT-2050/KXF-W6010CT-203/KXF-W4010CT-2050/KXF-W6010 only“AUTO BIAS”blinks. After approximately40 seconds“AUTO BIAS” lightsup.Each press of the MODE key changes the setting.1 “LEVEL” lights up: Recording level setting mode2 “BAL.” lights up: Recording balance setting mode3 “BIAS” lights up: Recording bias setting mode (Deck B of theCT-2050/KXF-W6010 only)4 “LEVEL”,“BAL.”,and “BIAS”go off: Counter display mode