Kenwood KDC-BT952HD Instruction Manual

Also see for KDC-BT952HD: Quick start guide

47 | KDC-X996/ KDC-BT952HD English | 48Audio AdjustmentsManual Equalizer ControlYou can adjust following Equalizer Control items.KDC-X996Band Item Range“BAND1” (62.5 Hz) “GAIN” Band level -9 –+9 dB“B.Ex” Bass Effect “ON”/ “OFF”“BAND2” (100 Hz) “GAIN” Band level -9 –+9 dB“BAND3” (160 Hz) “GAIN” Band level -9 –+9 dB“BAND4” (250 Hz) “GAIN” Band level -9 –+9 dB“BAND5” (400 Hz) “GAIN” Band level -9 –+9 dB“BAND6” (630 Hz) “GAIN” Band level -9 –+9 dB“BAND7” (1 kHz) “GAIN” Band level -9 –+9 dB“BAND8” (1.6 kHz) “GAIN” Band level -9 –+9 dB“BAND9” (2.5 kHz) “GAIN” Band level -9 –+9 dB“BAND10” (4 kHz) “GAIN” Band level -9 –+9 dB“BAND11” (6.3 kHz) “GAIN” Band level -9 –+9 dB“BAND12” (10 kHz) “GAIN” Band level -9 –+9 dB“BAND13” (16kHz) “GAIN” Band level -9 –+9 dB“BAND1” – “BAND13” “Q” Quality 1.35/ 1.5/ 2.0( : Factory setting)KDC-BT952HDBand Item Range“BAND1” (62.5 Hz) “GAIN” Band level -9 –+9 dB“B.Ex” Bass Effect “ON”/ “OFF”“BAND2” (160 Hz) “GAIN” Band level -9 –+9 dB“BAND3” (400 Hz) “GAIN” Band level -9 –+9 dB“BAND4” (1 kHz) “GAIN” Band level -9 –+9 dB“BAND5” (2.5 kHz) “GAIN” Band level -9 –+9 dB“BAND6” (6.3 kHz) “GAIN” Band level -9 –+9 dB“BAND7” (16 kHz) “GAIN” Band level -9 –+9 dB( : Factory setting)1 Select the sourcePressing the [SRC] button repeatedly switchessource.Select a source other than “STANDBY”.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Audio Control modePress the [VOL] knob.3 Enter Manual Equalizer Control modeTurn the [VOL] knob and press it when thedesired item is displayed.Select “Manual Equalizer”.4 Select the setting item to adjustTurn the [VOL] knob and press it when thedesired item is displayed.5 Make a settingTurn the [VOL] knob to select a setting value,and then press the [VOL] knob.6 Exit Audio Control modePress the [MENU] button for at least 1 second.⁄• When “iPod” is selected in the section curve Select> (page 46), Manual Equalizer Control isdisabled.• You can select for each source.Dual Zone SystemMain source and sub source (Auxiliary input) outputFront channel and Rear channel separately.Display Overview“2 Zone” Sets the Dual Zone System.“OFF”/ “ON”“2 Zone Rear Volume”* Adjust the volume of Rear channel.“0” — “35”“2 Zone Select”* Specifies the destination of sub source soundwhen the Dual Zone function is turned on.“Rear”/ “Front”* The Dual Zone System is set to “ON”.( : Factory setting)1 Select the sourcePressing the [SRC] button repeatedly switchessource.Select a source other than “STANDBY”.✍ SRC Select mode 2: Press the [SRC] button andthen turn the [VOL] knob. To determine theselected source, press the [VOL] knob.2 Enter Audio Control modePress the [VOL] knob.3 Turn the [VOL] knob and press it when thedesired item is displayed.Select “Pro Setup” > “Zone Control”.4 Select the item you want to setTurn the [VOL] knob and press it when thedesired item is displayed.5 Exit Audio Control modePress the [MENU] button for at least 1 second.⁄• Select Main source by [SRC] button.• Adjust the volume of Front channel by [VOL] knob.• The Audio Control has no effect on sub source.• There are following limitations when Dual Zone Systemis enabled.- There is no output from the subwoofer.- “Fader”, “Subwoofer Level” of

and DSP function are not available.