Kenwood KDC-BT952HD Instruction Manual

Also see for KDC-BT952HD: Quick start guide

81 | KDC-X996/ KDC-BT952HD English | 82Appendix• Sirius, XM and all related marks and logos aretrademarks of Sirius XM Radio Inc. All rights reserved.• PANDORA, the PANDORA logo, and the Pandora tradedress are trademarks or registered trademarks ofPandora Media, Inc., used with permission.• HD Radio Technology manufactured under licensefrom iBiquity Digital Corporation. U.S. and ForeignPatents. HD Radio™ and the HD, HD Radio, and “Arc”logos are proprietary trademarks of iBiquity DigitalCorp.• “Adobe Reader” is a trademark of Adobe SystemsIncorporated.• The “AAC” logo is a trademark of Dolby Laboratories.• The Bluetooth word mark and logos are owned bythe Bluetooth SIG, Inc. and any use of such marksby JVC KENWOOD Corporation is under license.Other trademarks and trade names are those of theirrespective owners.• iTunes is a trademark of Apple Inc.• “Made for iPod” and “Made for iPhone” mean that anelectronic accessory has been designed to connectspecifically to iPod, or iPhone, respectively, andhas been certified by the developer to meet Appleperformance standards. Apple is not responsible forthe operation of this device or its compliance withsafety and regulatory standards. Please note that theuse of this accessory with iPod, or iPhone may affectwireless performance.• iPhone, iPod, iPod classic, iPod nano, and iPod touchare trademarks of Apple Inc., registered in the U.S. andother countries.• Android is a trademark of Google Inc.• BlackBerry®, RIM®, Research In Motion® and relatedtrademarks, names and logos are the property ofResearch In Motion Limited and are registered and/orused in the U.S. and countries around the world. Usedunder license from Research In Motion Limited.Accessories/ Installation ProcedureAccessories1..........12..........23..........44..........453 m (9.5 ft) ..........1Installation Procedure1 To prevent a short circuit, remove the key from theignition and disconnect the - battery.2 Make the proper input and output wireconnections for each unit.3 Connect the speaker wires of the wiring harness.4 Connect the wiring harness wires in the followingorder: ground, battery, ignition.5 Connect the wiring harness connector to the unit.6 Install the unit in your car.7 Reconnect the - battery.8 Press the reset button.2WARNINGIf you connect the ignition wire (red) and the battery wire(yellow) to the car chassis (ground), you may cause a shortcircuit, that in turn may start a fire. Always connect thosewires to the power source running through the fuse box.¤• Mounting and wiring this product requires skills andexperience. For safety’s sake, leave the mounting and wiringwork to professionals.• Make sure to ground the unit to a negative 12V DC powersupply.• Do not install the unit in a spot exposed to direct sunlightor excessive heat or humidity. Also avoid places with toomuch dust or the possibility of water splashing.• Do not use your own screws. Use only the supplied screws.Using wrong screws, could damage the unit.• If the power is not turned ON (“Protect” is displayed), thespeaker wire may have a short-circuit or touched thechassis of the vehicle and the protection function mayhave been activated. Therefore, the speaker wire should bechecked.• If your car’s ignition key switch does not have an ACCposition, connect the ignition wires to a power sourcethat can be turned on and off with the ignition key. If youconnect the ignition wires to a constant-voltage powersource, as with battery wires, the battery may die.• If the console has a lid, make sure to install the unit so thatthe faceplate will not hit the lid when it is closed or opened.• If the fuse blows, first make sure the wires are not touchingother parts to cause a short circuit, and then replace the oldfuse with one with a new the same rating.• Insulate unconnected wires with vinyl tape or other similarmaterials. To prevent a short circuit, do not remove the capson the ends of the unconnected wires and terminals.• Connect the speaker wires correctly to the correspondingterminals. The unit may be damaged or fail to work if youshare the - wires or ground them to any metal part in thecar.• When connecting only two speakers, connect theconnectors either to both of the front output terminalsor to both of the rear output terminals (do not mix frontand rear terminals). For example, if you connect the +connector of the left speaker to a front output terminal, donot connect the - connector to a rear output terminal.• After the installing the unit, check whether the brake lamps,blinkers, wipers, etc. on the car are working properly.• Mount the unit so that the mounting angle is 30° or less.• Reception may become poor if there aremetal objects near the Bluetooth antennaBluetooth antenna unitFor Good ReceptionTo assure good reception, note the following:• Communicate with the cell-phone within the line-of-sight distance of 10 m (30 ft). The communicationrange becomes shorter depending on thesurrounding environment. The communicationrange also becomes shorter when there is anobstacle between this unit and the cell-phone. Theabove maximum communication range (10 m) isnot always assured.• A broadcast station or walkie-talkie located nearbycan interfere with communication due to a toostrong signal.