14 | KDC-U7056DAB/ KDC-U7056BT/ KDC-U7056BTL English | 15DSP settings4-4. Speaker settingThe speaker X’Over is automatically set when theposition and size of each speaker are selected fromthe following items.1 Press [SRC] to select a source other thanStandby (“STANDBY”).Refer to (page 10).2 Press [Control] knob.Enters the Function setting mode.3 Select “Audio Control” > “Pro Setup” >“Speaker Setting” using [Control] knob.For how to use [Control] knob, refer to <3-3. Howto select the item> (page 9).4 Select a speaker type using [Control] knob.Speaker type Setting item Setting value“Front” Front speakerlocation“Door”, “On Dash”, “Under Dash”“SIZE” Front speaker size“O.E.M.”, “8cm”, “10cm”, “12cm”,“13cm”, “16cm”, “17cm”, “18cm”,“4x6”, “5x7”, “6x8”, “6x9”, “7x10”“TW” Tweeter size“None”, “Small”, “Medium”, “Large”“Rear” Rear speakerlocation“Door”, “Rear Deck”(“2nd Row”, “3rd Row”[1])“SIZE” Rear speaker size“None”, “O.E.M.”, “8cm”, “10cm”,“12cm”, “13cm”, “16cm”, “17cm”,“18cm”, “4x6”, “5x7”, “6x8”, “6x9”,“7x10”“SubWoofer” “SIZE” Speaker Size Subwoofer“None”, “16cm”, “20cm”, “25cm”,“30cm”, “38cm Over”(Colored text: Factory setting)[1] Value set when “Minivan” or “Minivan (Long)” is selectedas described in <4-3. Car type selection> (page 13).When Speaker network is set to 3 waySpeaker type Setting item Setting value“Tweeter” “SIZE” Tweeter size“Small”, “Medium”, “Large”“Mid Range” Mid RangespeakerlocationMid range speaker location“Door”, “On Dush”, “Under Dush”“SIZE” Mid range speaker size“O.E.M.”, “8cm”, “10cm”, “12cm”,“13cm”, “16cm”, “17cm”, “18cm”,“4x6”, “5x7”, “6x8”, “6x9”, “7x10”“Woofer” “SIZE” Subwoofer size“None”, “16cm”, “20cm”, “25cm”,“30cm”, “38cm Over”4-5. X’Over settingFine adjusting the following setting valuescorresponding to the X’Over values set in thesection <4-4. Speaker setting> (page 14).1 Press [SRC] to select a source other thanStandby (“STANDBY”).Refer to (page 10).2 Press [Control] knob.Enters the Function setting mode.3 Select “Audio Control” > “Pro Setup” >“X’Over” using [Control] knob.For how to use [Control] knob, refer to <3-3. Howto select the item> (page 9).4 Select a speaker type using [Control] knob.Speaker type Setting item Setting value“Front” “FC” Front high pass filterThrough, 30, 40, 50, 60, 70, 80, 90,100, 120, 150, 180, 220, 250 Hz“SLOPE”[1] Front high pass slope-6, -12, -18, -24 dB/Oct“GAIN” Front gain-8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB“Rear” “FC” Rear high pass filterThrough, 30, 40, 50, 60, 70, 80, 90,100, 120, 150, 180, 220, 250 Hz“SLOPE”[1] Rear high pass slope-6, -12, -18, -24 dB/Oct“GAIN” Rear Gain-8, -7, -6, -5, -4, -3, -2, -1, 0 dB“SubWoofer” “FC” Subwoofer low pass filter30, 40, 50, 60, 70, 80, 90, 100, 120,150, 180, 220, 250, Through Hz“SLOPE”[1] Subwoofer slope-6, -12, -18, -24 dB/Oct“GAIN” Subwoofer gain-8, -7, -6, -5, -4, -3, -2, -1, 0 dB“PHASE” Subwoofer phase“REV” (180°)/ “NML” (0°)“Tweeter” “FC” Shelving filter1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 kHz“Volume” Tweete volume-8, -7, -6, -5, -4, -3, -2, -1, 0 dB(Colored text: Factory setting)[1] Displayed only when “FC” is set to ”30” - “250”.5 Select a setting item using [Control] knob.6 Select a setting value using [Control] knob.Exiting from the Function setting modePress and hold [1/6].When Speaker network is set to 3 waySpeaker type Setting item Setting value“Tweeter” “FC” Tweeter high pass filter1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 kHz“SLOPE” Tweeter slope-6, -12 dB/Oct“GAIN” Tweeter gain-8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB“PHASE” Tweeter phase“REV” (180°)/ “NML” (0°)“Mid LPF” “FC” Mid range low pass filter1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5,Through kHz“SLOPE” Mid range low pass slope-6, -12 dB/Oct“GAIN” Mid range gain-8, -7, -6, -5, -4, -3, -2, -1, 0 dB“PHASE” Mid range phase“REV” (180°)/ “NML” (0°)“Mid HPF” “FC” Mid range high pass filterThrough, 30, 40, 50, 60, 70, 80, 90,100, 120, 150, 180, 220, 250 Hz“SLOPE” Mid range high pass slope-6, -12 dB/Oct“GAIN” Mid range gain-8, -7, -6, -5, -4, -3, -2, -1, 0 dB“PHASE” Mid range phase“REV” (180°)/ “NML” (0°)“Woofer” “FC” Woofer low pass filter30, 40, 50, 60, 70, 80, 90, 100, 120,150, 180, 220, 250, Through Hz“SLOPE” Woofer low pass slope-6, -12 dB/Oct“GAIN” Woofer gain-8, -7, -6, -5, -4, -3, -2, -1, 0 dB“PHASE” Woofer phase“REV” (180°)/ “NML” (0°)5 Select a setting item using [Control] knob.6 Select a setting value using [Control] knob.Exiting from the Function setting modePress and hold [1/6].
