Kenwood KRF-V5090D Instruction Manual

Also see for KRF-V5090D: Instruction manual Service manual

15 ENPreparing for surround soundSpeaker settingsTo enable you to obtain optimum enjoyment from this model’s listeningmodes, make sure to complete the speaker settings (Subwoofer, Front,Center, Surround and Surround Back speakers) as described below.MULTI CONTROLSETUPSETUPPOWERON/OFFON/STANDBYMULTICONTROLRECEIVER1Turn on the power to this model by pressing POWER ON/OFFand ON/STANDBY or RECEIVER key.If you want to use the remote control unit, press the TUNER, MD/TAPE, VIDEO 1, VIDEO 2 or AUX key on the remote control unitto set it to the receiver control mode.2Press the SETUP key to enter the SETUP mode and use theMULTI CONTROL knob or MULTI CONTROL %/ fikeys for thefollowing displays.1 SP SETUP2 TESTTONE3 DISTANCE4 LFE LVL5 EXITThe flow of the SETUP is as follows;SP SETUP TESTTONE DISTANCE LFE LEVEL EXITFront LeftCenterFront RightSurround RightSurround LeftSurround Back RightSurround Back LeftSubwooferSP SystemLCRRSRBLBLSSWLCRRSRBLBLSSWMANUALAUTO2Way 2SpeakerFull Range2Way 3SpeakerCustomSubwooferFrontCenterSurroundSurround BackSubwoofer Re-mix(KRF-V6090D only)• If you have selected “SPEAKER” as the Surround Back setting,“RB”/ ”Surround Back Right” and “LB”/ ”Surround Back Left” arenot appeared but ”BS” / “Surround Back” is appeared on theDisplay.3Select a speaker system.1 Select SP SETUP and press the SETUP key again so that thespeaker system indication “SP SYSTEM” scrolls across thedisplay.2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keysto select the speaker system setting.1 CUSTOM : For general speakers.2 FULL RANGE : For selected KENWOOD speaker - for example,KS-2200HT, KS-4200EX.3 2WAY 2SPKR : For selected KENWOOD speaker – forexample, KS-3200HT, KS-3200EX, KS-5200HT,KS-5200EX, KS-7200HT.4 2WAY 3SPKR : For selected KENWOOD speaker – forexample, KS-8200HT, KS-8200EX.• The selection of FULL RANGE, 2WAY 2SPKR or 2WAY 3SPKRshould only be used with 6 channels speaker system setting.• When the setting FULL RANGE, 2WAY 2SPKR or 2WAY 3SPKRis selected, the procedure skips to step 4.3 For general speaker setting, use the MULTI CONTROL knobor MULTI CONTROL %/fi keys to select CUSTOM and pressthe SETUP key again.• The subwoofer setting indication “SUBW ON” appears.4 Use the MULTI CONTROL knob or MULTI CONTROL %/fikeys to select the appropriate subwoofer setting.1 SUBW ON : Subwoofer setting mode to this model is ON.2 SUBW OFF : Subwoofer setting mode to this model is OFF.• The initial setting is “SUBW ON”.• When the setting “SUBW OFF” is selected, the Front speakersare automatically set to “FRNT LRG” and the procedure skips tostep 7.Before step 7, press the SETUP key to accept the setting.• When Subwoofer output sound is required, select “FRNT NML”.5 Press the SETUP key to accept the setting.• The Front speakers setting indication “FRNT LRG” appears.6 Use the MULTI CONTROL knob or MULTI CONTROL %/fikeys to select the appropriate front speakers setting.1 FRNT LRG (large) : Large Front speakers are connectedto this model.2 FRNT NML (normal) : Average size Front speakers areconnected to this model.• For “FRNT LRG” selection, no sound will be heard fromSubwoofer speaker even when it is set to ON. However, if youselect “SW RE-MIX ON” when Subwoofer is selected, you willbe able to hear sound from the Subwoofer.When in STEREO mode, the sound goes directly to Frontspeaker.7 Press the SETUP key to accept the setting.• The Center speaker setting indication “CNTR NML” appears.Continued to next page