Kenwood KRF-V7090D Instruction Manual

Also see for KRF-V7090D: Service manual

34 ENENGLISHConvenient functionsCenter Image mode (Neo:6 Music mode only)In the CENTER IMAGE setting mode of the Neo:6 MUSIC listen mode,it is possible to enhance the center channel audio by adjusting the centersignal component.1 Press the SOUND key, then press the ∧/∨ keys or MULTI @/#keys until “CENTER IMAGE” appears on the display.L RSP MUTEA B CLIPSTEREO NEO:6AUTO DETECT• When the center speaker is switched OFF, this mode will not beeffective.2 Use the MULTI CONTROL knob or MULTI %/fi keys to adjust theleft-center-right output.LS SBRLFESP MUTEA B CLIPNEO:6AUTO DETECT• Adjust the center component level.3 Press the SOUND key again to return to the input indication.Dual Mono mode (Dolby Digital mode only)When the Dolby Digital source have Multiplex sound, you can selectMain / Sub sound for Audio output.1 Press the SOUND key, then press the ∧/∨ keys or MULTI @/# keysuntil “DUAL MONO” appears on the display.• This can be selected only if CD/DVD, DVD/6CH, VIDEO 2 or VIDEO 3is selected as the source and the LISTEN mode is set to “DOLBYDIGITAL.”2 Use the MULTI CONTROL knob or MULTI %/fi keys for thefollowing selection.1 Main : Multiplex Main channel output.2 Sub : Multiplex Sub channel output.3 Main + Sub : Multiplex Main + Sub channel output.4 Stereo : M a i n c h a n n e l f r o m t h e l e f t s p e a k e r ./ Sub channel from the right speaker.LFESP MUTEA B CLIPDIGITAL DOLBY DIGITAL STEREOAUTO DETECT• The adjustment item is displayed for approximately 20 seconds.3 Press the SOUND key again to return to the input indication.96kHz LPCM playbackThe receiver is compatible with the 96kHz LPCM playback. To play a96kHz DVD, set the listen mode other than DSP mode.(96kHz fs indicator lights up)• When in FULL AUTO input mode and the listen mode is set to DSPmode, the listen mode will automatically be STEREO.• When in DIGITAL MANUAL input mode and the listen mode is set toDSP mode, “96kHz LPCM” will appear in the display and no sound canbe heard from the speakers.Use the LISTEN MODE knob, LISTEN MODE key or STEREO key toselect STEREO mode to output sound from the speakers.Display dimmer adjustmentThe dimmer function lets you select the brightness of the receiver'sdisplay. You might find this useful if you darken your room to watchmovies or listen to music.If you want to use the remote control unit, press the VIDEO 1,VIDEO 2, VIDEO 3, MD/TAPE, PHONO, AV AUX or TUNER key onthe remote control unit to set it to the receiver control mode.Each time you press the DIMMER key, the display brightnesschanges among the three available settings.Select the brightness level you find most pleasing.L RSP MUTEA B CLIPLFEL RSPAL RSPADOLBY PL II xAUTO DETECTDOLBY PL II xAUTO DETECTDOLBY PL II xAUTO DETECTSleep timerThe sleep timer function turns the receiver OFF (to the standby mode)automatically when the set timer period has elapsed. The sleep timerperiod can be set in 10-minute steps up to 90 minutes.Press the SLEEP key repeatedly until the desired period beforeturning the receiver OFF (standby mode) is displayed.• Each press increments the sleep timer period by 10 minutes.10 = 20 = 30 .....70 = 80 = 90 = Cancel = 10 = 20 = ...The “SLEEP” indicator lights upLSL SRC RSP MUTEA B CLIPLFEDIGITAL DOLBY DIGITAL STEREOSLEEPAUTO DETECT• Pressing the SLEEP key after the sleep timer has started allows youto check the remaining time period.• To cancel the sleep timer, turn the receiver OFF (standby mode) orpress the SLEEP key repeatedly until the Sleep timer indicatordisappears.