Kenwood KRF-X9080D Instruction Manual

Also see for KRF-X9080D: Service manual

19 ENENGLISHPreparing for surround soundSpeaker settingsTo enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (Subwoofer, Front,Center, and Surround Speakers) as described below.1Turn on the power to this receiver by pressing the POWERON/OFF and ON/STANDBY key or POWER RCVR key.2For the remote control, press and hold the TUNER key formore than 3 seconds to switch to receiver mode.3Press the SETUP key to enter the SETUP mode.Use ∧∧∧∧∧/∨∨∨∨∨keys or @/ # keysfor the following displays.1 SP SETUP2 TEST TONE3 BASS PEAK4 SP DISTANCE5 LFE LEVEL6 DISP MODE7 EXITThe flow of the SETUP is as follows:SPSETUPTESTTONE EXITFront LeftCenterFront RightSurround RightSurround Back RightSurround Back LeftSurround LeftSubwooferDisplay SelectorDisplay ListenSubwooferFrontCenterSurroundSurroundBackSubwooferRe-mixT. TONEMANUALT. TONEAUTOLCRSRSBRSLSBLSWBASSPEAKLFELEVELDISPMODESPDISTANCELCRSRSBRSBLSLSW4Select a speaker system.If you have THX certified speakers, please set them to NML/THX.1 Select the SP SETUP and press the SETUP key again so thatthe Subwoofer setting indication “SUBW ON” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE2 Use the MULTI CONTROL knob or Multi (%/fi) keys to selectthe appropriate Subwoofer setting.1 SUBW ON : Subwoofer setting mode to the receiver isON.2 SUBW OFF : Subwoofer setting mode to the receiver isOFF.• The initial setting is “SUBW ON”.• When the setting “SUBW OFF” is selected, the Front Speakersare automatically set to “FRNT LARGE” and the procedure skipsto step 6.Before step 6, press the SETUP key to accept the setting.• When Subwoofer output sound is required, select “FRNT NML/THX”, or select both “FRNT LARGE” and “SW RE-MIX ON”.3 Press the ∧∧∧∧∧ key or # key to accept the setting.• The Front Speakers setting indication “FRNT” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE4 Use the MULTI CONTROL knob or Multi (%/fi) keys to selectthe appropriate Front Speakers setting.1 FRNT NML/THX : Average size Front Speakers areconnected to the receiver.2 FRNT LARGE : Large Front Speakers are connectedto the receiver.• For “FRNT LARGE” selection, no sound will be heard fromSubwoofer even when it is set to on. However, if you select“SW RE-MIX ON” when Subwoofer is selected, you will be ableto hear sound from the Subwoofer.When in STEREO mode, the sound goes directly to FrontSpeaker.5 Press the ∧∧∧∧∧ key or # key to accept the setting.• The Center Speaker setting indication “CNTR” appears.6 Use the MULTI CONTROL knob or Multi (%/fi) keys to selectthe appropriate Center Speaker setting.If you selected “LARGE” as the Front Speakers setting,1 CNTR NML/THX : An average size Center Speaker isconnected to the receiver.2 CNTR LARGE : A large Center Speaker is connectedto the receiver.3 CNTR OFF : Center Speaker setting mode to thereceiver is OFF.If you selected “NML/THX” as the Front Speakers setting,1 CNTR NML/THX : An average size Center Speaker isconnected to the receiver.2 CNTR OFF : Center Speaker setting mode to thereceiver is OFF.SETUP MULTI CONTROLON/STANDBYPOWER ON/OFFPOWER RCVRSetup(Multi %/ fi,@/#)TUNERSOUNDSoundContinued to next page.