Kenwood TK-2200L Service Manual

Also see for TK-2200L: Product brochure Instruction manual

TK-2200L44-5. Programming software KPG-88D descriptionKPG-88D is the programming software for the transceiversupplied on a CD-ROM. This software runs under Windows 98,ME, Windows 2000 or XP on an IBM-PC or compatible machine.The data can be input to or read from the transceiver andedited on the screen. The programmed or edited data can beprinted out. It is also possible to tune the transceiver.5. Clone Mode5-1. Outline"Clone Mode" copies the transceiver data to anothertransceiver.The dealer can copy the transceiver data to anothertransceiver even without the use of a personal computer.5-2. ExampleThe transceiver can copy the programming data to one ormore transceivers via RF communication.The clone source and clone target/s must be in Clone mode.5-3. Operation1. To switch the clone target/s to Clone mode, press and hold the[PTT] and [Side2] keys while turning the transceiver power ON.2. Wait for 2 seconds. The LED will light orange and thetransceiver will announce "Clone".3. Select a channel table number using Side1(incrementchannel table) and Side2(decrement channnel table) keys.4. To switch the clone source to Clone mode, press and hold the[PTT] and [Side2] keys while turning the transceiver power ON.5. Wait for 2 seconds. The LED will light orange and thetransceiver will announce "Clone".6. Select the same channel table number as the clone target/s.7. Press [PTT] on the clone source to begin data transmission. Whenthe clone target starts to receive data, the LED will light green.When the clone source finishes sending data, a"confirmation" tone will sound.REALIGNMENTIf data transmission fails while cloning, an "error" tone willsound from the Target unit.8. If the cloning fails, no data will be available in the Targetunit when it is returned to User mode.9. When the cloning is successful, the Target unit's "Scan"function will return to its default value (Scan = OFF).Notes:• The dealer can clone data to two or more transceivers byrepeating the above procedures.• If the transceivers Clone Mode is configured as "Disabled",the transceiver cannot enter Clone mode.• The table shown below will cover the frequency tables usedfor wireless cloning.• A unit cannot be a "Source Unit" if it is unprogrammed. If[PTT] is pressed, an "error" tone will sound.• Once a unit is set to be the Source, it cannot be a targetafter the data has been transmitted. This protects the datain the Source unit.• If the Target unit is cloned successfully, it will return toUser Mode.• If the Target unit is not cloned successfully, the led willremain Orange.• The Source Unit and Target Unit must be of the same modeltype and destination in order for Clone to operate.• Clone mode cannot be accessed if “Super Lock” is activated.• Electronic interface may cause a failure in data transferduring Wireless Clone, such as when waveforms orelectromagnetics are being performed at the workbench.• Clone mode can be used ONLY by the authorized servicepersonnel.• The Clone mode setting must be configured as "Disable"before being delivered to the end-user.• To clone, replace the antenna from both the sourcetransceiver and the target transceiver with a dummy load.• The transmit output power is automatically set to Lowin Clone mode.Tuning cable(E30-3216-05)RF Power meteror SSGGray +Gray/Black –1.5D-XV Lead wire +1.5D-XV Shield wire –}}SPMICKPG-22 or KPG-22A or KPG-22A + KCT-53UIllustration is KPG-22.KPG-88DIBM-PCKPG-22TransceiverPCD-SUB(25-pin)TransceiverPCKPG-22AD-SUB(9-pin)TransceiverPCKPG-22AKCT-53UUSBFig. 1Clone Frequency TableTable Frequency Table FrequencyNumber (MHz) Number (MHz)1 151.6250 15 151.77502 151.9550 16 151.86503 154.5700 17 151.89504 154.6000 18 151.92505 151.7000 19 152.70006 151.7600 20 154.49007 151.8200 21 154.51508 151.8800 22 154.52759 151.9400 23 154.540010 151.5125 24 154.600011 151.6550 25 154.655012 151.6850 26 158.400013 151.7150 27 158.407514 151.7450