Kenwood TK-3118 Service Manual

Also see for TK-3118: Service manual

5TK-3118TK-260 :K, K22) Channel settingOperation:After entering Self-Programming Mode Press the [ LOW ] key.The LCD changes toCH 1 1When you press the PTT switch after setting the data, youcan continue to the next Item. (Refer to page8 item 6)… REALIGNMENT/ 模式组合2) 信道设定操作：进入自台编程模式后按[LOW]键。LCD变为CH 1 1当您在设置数据后按下PTT开关，您便可继续到下一项。（请翻阅8页项目6）∗1 Step change for setting the frequencyMHz step: Routed the Channel selector while pressing the[1] key.5kHz or 6.25kHz step: Press the [SCAN] keySelecting the setting items Display Setting contents(Example)Channel range from 1 to50.Setting the channel numberWhen a channel number is notset, the following items will notbe selected.(CH 1 1 )Blank100.00000MHz~549.99375MHz(UHF: 6.25kHz(Default) /5kHz Step)∗1Default (C): 450.000MHz(C4): 410.000MHzSetting the receive QT/DQTWhen a channel number is not set,this item will be skipped.(…… 2 )(OFF 3 ) OFFQT(QT frequenciestable)∗2: 67.0Hz ~ 250.3HzDQT(DQT Normal/Inverse table)∗2: 023 ~ 754 Normal settingDQT(DQT Normal/Inverse table)∗2: -023 ~ -754 Inverse settingSetting the receive frequencyWhen a receive frequency is notset ("blank" is set), the followingitems will not be selected. (Itemnumbers 3 to 12 are not selected.)When "blank" is set, you will returnto "setting the channel number".Setting the transmit frequency Same asRX Display(This is itemnumber "4".)Same content as "Settingthe received frequency"Setting the transmit QT/DQTWhen a transmit frequency is notset, this item will be skipped.Same asRX Display(This is itemnumber "5".)Same content as"Setting the receive QT/DQT"(450.000 2 )(q 100.0 3 )(d 023 3 )(d -023 3 )Setting the option signalling 0: None 1: DTMFSetting the BUSY CH Lockout(BCL)OFF: OFF 1: Carrier2: QT/DQT 3: DTMFF o r s e t t i n g n u m b e r" 3 " ( D T M F ) , i f o f O p t i o nSignaling is changed from"DTMF" to "None" before theBCL setting is entered, theBCL setting contents will beautomatically set to "OFF"(OFF).Setting the Beat Shiftfunction ON or /OFFOFF: No ON: YesSetting Scan DELETE / ADD del: Scan DELETEAdd: Scan ADDSetting Wide / Narrow 0: Narrow 1: WideSetting the SP UnmuteWhen option signaling is setto "0" (None), this item will beskipped.0: Carrier or QT/DQT1: Carrier + DTMF or QT/DQT + DTMFF o r s e t t i n g n u m b e r " 1 "(Carrier + DTMF or QT/DQT +DTMF), if Option Signaling ischanged from "DTMF" to"None" before the SP Unmutesetting item is entered, the SPUnmute setting contents willbe automatically set to "0"(Carrier or QT/DQT).Setting the transmit power H: High powerL: Low power(0 6 )(OFF 7 )(OFF 8 )(Add 9 )(0 10 )(0 11 )(H 12 )∗1 设置频率的步进MHz档：按下[1]键的同时确定信道选择器的方向。5kHz或6.25kHz档: 按下[SCAN]键选择设置项目显示设置内容(例如)信道范围1-50。设置信道编号当未设置信道号时，将不选择以下项目。(CH 1 1 )设置接收频率当未设置接收频率时(设置为"空白")，将不选择以下项目。(不选择项目编号3-12。)当设置为"空白"时，您将返回到"设置信道号"。(…… 2 )(450.000 2 )空白100.00000MHz~549.99375MHz(UHF: 6.25kHz(缺省) /5kHzStep)*1缺省 (C): 450.000MHz(C4): 410.000MHz设置接收 QT/DQT当未设置信道号时，该项目将跳过。(OFF 3 ) OFFQT(QT 频率表 )*2:67.0Hz ~ 250.3HzDQT(DQT 正常/反向表)*2:023 ~ 754 正常设置DQT(DQT 正常/反向表)*2:-023 ~ -754 反向设置(q 100.0 3 )(d 023 3 )(d -023 3 )设置发射频率与接收显示相同(该项目号为编号"4".)与 "接收频率" 内容相同。设置传送 QT/DQT当未设置发射频率时，该项目将跳过。与接收显示相同(该项目号为编号"5".)与 "设置接收 QT/DQT "内容相同。设置可选信令 0: 无 1: DTMF设置繁忙信道锁定 (BCL) OFF: 关 1: 载波2: QT/DQT 3: DTMF对于设置 "3" (DTMF)，如果在输入B C L 设置之前可选信令设置从" D T M F " 变为"无"，则B C L 设置内容将自动设置为 " O F F "(关)。设置差拍偏移功能ON或OFF OFF: 否 ON: 是设置扫描删除／添加扫描 del: 扫描删除Add: 扫描添加设置宽／窄带 0: 窄带 1: 宽带设置SP不静音当选择信令的选择被设置到"0"(无)时，该项目将跳过。0: 载波或 QT/DQT1: 载波 + DTMF或QT/DQT + DTMF对于设置编号"1"(载波+DTMF或QT/DQT+DTMF)，如果在输入S P 不静音设置项目之前可选信令设置从"DTMF"变为 "无"，则SP不静音设置内容将自动设置为"0" (载波或QT/ DQT)。设置发射功率 H: 高功率L: 低功率(0 6 )(OFF 7 )(OFF 8 )(Add 9 )(0 10 )(0 11 )(H 12 )