Kenwood TK-6110 Service Manual

Also see for TK-6110: Brochure & specs Brochure & specs Service manual Instruction manual

Contents

5TK-61102. Scanning2-1. Start ScanningYou can start scanning when 1 priority channel and atleast 1 ADD channel, or 2 or more ADD channels are se-lected. The transceiver must be in the normal receivingmode (releasing PTT).Press the key programmed to the scan, the scan starts.The “SCN” (scan) icon appears on the main display and“SCAN” or revert channel appears on the 8-digit alphanu-meric display.2-2. Stop ScanningThe scan stops temporarily if the following conditions aresatisfied.1) A carrier is detected, then signalling matches on channelfor which receive the signalling is set by the program-ming software.2) A carrier is detected on the channel for which receivingsignalling is not set by the programming software orwhen the monitor (signalling cancel) function is activated.2-3. Types of Scan Channel1) Priority channel is the most important channel for thescan, and always detects a signal during scan and whenthe scan stops temporarily.2) Non-priority channels detects a signal during scan andwhen scan stops temporarily.2-4. Setting Priority ChannelPriority channel can be set as follows with the program-ming software (KPG-59D).1) Specify priority channel as fixed priority channel.2) Make selected channels, priority channels.2-5. Scan Type Depending on the Priority Channel1) When no priority channels are set : Only the non-prioritychannels are scanned.If the transceiver stops on a non-priority channel, prioritychannel is still checked for signals at the specified timeintervals.If the transceiver detects a signal on a priority channel, itpauses at the priority channel and starts receiving thecalls.2) When priority channel is set : Either priority channel isscanned.If a priority channel stops temporarily, it stops until thereis no signal on the priority channel.2-6. Revert ChannelThe revert channel is used to transmit during scanningand set by the programming software (KPG-59D).1) Last called channelThe transceiver reverts to the last called channel duringthe scan.2) Last used channelThe transceiver reverts to the last used (transmitted)channel during scan. “Last used” revert channel in-cludes talkback function.3) Selected with talkbackThe transceiver reverts to the channel before scanning orthe channel that you changed during scan.4) Selected channelThe transceiver reverts to the channel before scanning orthe channel that you changed during scan.While the transceiver pauses scanning, the revert chan-nel becomes the channel you selected with [CH UP], [CHDW], [CH1] to [CH5] in the last step.5) Priority with talkbackThe transceiver reverts to the priority channel.If you press PTT during a resume timer (dropout delaytime, TX dwell time) or calling, you can transmit on cur-rent channel to answer to the call however revert channelis set to priority channel.After resume time, scan re-starts and transmission chan-nel is return to priority channel.6) PriorityThe transceiver reverts to the priority channel.2-7. Scan EndWhen you press the key once again, programmed to thescan function during scan mode, the scan ends.The scan icon “SCN” and “SCAN” or revert channel (pro-grammable) display goes off.2-8. Temporarily Delete/AddIt is possible to delete or add channel temporarily duringscan. When scan stops on unnecessary channel for ex-ample by interference of the other party, activate the delete/add function (for example press the key), then that channelis deleted temporarily and scan re-start immediately.When you would like to add the deleted channel tempo-rarily to scan sequence, select the desired (deleted) channelduring scan, activate the delete/add function (for examplepress the key) before scan re-start.That channel is added temporarily to scan sequence. Thetemporary deleted or added channels are returns to pre-setdelete/add, when the transceiver exits from scan mode.3. Optional FeaturesYou can use these features using the programming soft-ware (KPG-59D).3-1. Beep TonesThe beep tones (power on tone, control tone, warningtone, alert tone) are individually programmable to the fixedlevel 0 to 31 or follow the mechanical volume position.3-2. Minimum VolumeThe minimum volume is programmable (0 to 31). Thetransceiver remains the minimum volume level however themechanical volume position is set to zero.3-3. BCL (Busy Channel Lockout) OverrideYou can transmit in spite of Busy Channel Lockout situa-tion. For example : To make an emergency voice call.To transmit under busy channel lockout situation, pressPTT once more within approx. 500ms after the PTT release.OPERATING FEATURES