8TK-61105-13. Emergency CallWhen the Emergency function (key) is activated, the ra-dio enters the “Emergency Mode”.In this mode, the radio automatically switches to the pro-grammed “Emergency Channel” and starts transmissionwith the Emergency ID Code programmed in an installedANI Board (dependent on ANI board capabilities and pro-gramming). The LCD display (Emergency Text) and the TXLED operation are dependent on the “Emergency CH Dis-play” settings.6. 2-Tone2-Tone signalling opens the squelch only when the RA-DIO receives a proper 2-Tone code that is the same as thepre-programmed 2-Tone for the channel. When the RADIOreceives a 2-Tone code, the CALL icon flashes.If Transpond has been programmed, the RADIO will re-turn an acknowledgment signal automatically after receivingthe 2-Tone code.If Alert Tone has been programmed, an Alert Tonesounds after receiving a 2-Tone code. Unmute condition iscanceled and the CALL icon goes off when ; (1) pressing the[MON] Key, (2) hanging the microphone on its hook, (3) mut-ing continues for 10 seconds. (If “Auto Reset” has beenprogrammed)7. DTMFDTMF Signalling opens the squelch only when the RA-DIO receives a proper DTMF code that is the same as thepre-programmed “Primary Code (Individual ; 1~7digits)” or“Secondary Code (Group ; 1~7digits)”. When the RADIO re-ceives a correct code, the CALL icon flashes.If Transpond has been programmed, the RADIO will re-turn an acknowledgment signal automatically after receivingthe DTMF code.If Alert Tone has been programmed, an Alert Tonesounds after receiving a DTMF code. Unmute condition iscanceled and the CALL icon goes off when ; (1) pressing the[MON] Key, (2) hanging the microphone on its hook, (3) mut-ing continues for 10 seconds (If “Auto Reset” has been pro-grammed), and (4) receiving reset code. (Primary code +“#” or secondary code + “#”)8. Data Programming (PC Mode)8-1. Preparation and ConnectionThe TK-6110 transceiver is programmed by using a per-sonal computer, programming interface cable KPG-46, andprogramming software KPG-59D.The programming software can be used with an IBM-PCor compatible machine. Figure 2 shows the setup for pro-gramming.8-2. Programming Interface Cable KPG-46 DescriptionThe KPG-46 is required to interface the transceiver withthe computer. It has a circuit in its D-sub 25pin connectorcase that converts RS-232C logic level to TTL level.KPG-46 is used to connect between transceiver micro-phone connector and RS-232C serial port of computer.8-3. Programming Software KPG-59D DescriptionKPG-59D is the programming software for TK-6110 sup-plied on two 3.5" floppy disks. This software runs under MS-DOS version 3.1 or later, and Windows MS-DOS prompt onan IBM-PC or compatible machine.The data can be input to or read from TK-6110 and editedon the screen. The programmed or edited data can beprinted out. It is also possible to tune the transceiver.We recommend that install KPG-59D for example toharddisk first then use it.Fig. 2OPERATING FEATURES / REALIGNMENTKPG-46IBM-PCKPG-59DTK-6110REALIGNMENT1. ModeUser modePC mode PC programming modePC test modePC tuning modePanel test mode Panel tuning modeClone modeMain programming modeMode FunctionUser mode Customer use this modePC mode Communication between the radio andPC (IBM compatible).It requires the KPG-59D.PC programming Frequency, signalling and features writemode to the radio and read from the radio.PC test mode Check the radio using the PC.This feature is included in the FPU.Panel test mode Dealer uses to check the fundamental(Refer to ADJUSTMENT) characteristics.Main programming Re-write to firmware of the flash ROM.mode