Kenwood TM-D710GE Instruction Manual

Also see for TM-D710GA: Instruction manual Quick start guide

SCAN-2VFO SCANVFO Scan monitors all frequencies tunable on the band, usingthe current frequency step size.1 Select your desired band.2 Press [VFO] (1s).• Scan starts at the current frequency.• The 1 MHz decimal blinks while scanning is in progress.• To reverse the scan direction, turn the Tuning control clockwise(upward scan) or counterclockwise (downward scan). You canalso press microphone [UP]/ [DWN].3 To quit VFO Scan, press [VFO] again.MEMORY SCANUse Memory Scan to monitor all Memory channels programmedwith frequency data.1 Select your desired band.2 Press [MR] (1s).• Scan starts at the current frequency.• The 1 MHz decimal blinks while scanning is in progress.• To reverse the scan direction, turn the Tuning control clockwise(upward scan) or counterclockwise (downward scan). You canalso press microphone [UP]/ [DWN].3 To quit Memory Scan, press [MR] again.Note:◆ At least 2 Memory channels must contain data and must not be locked outof scan.◆ The L0/U0 to L9/U9 Memory channels will not be scanned.◆ You can also start Memory Scan when in Channel Display mode. WhileScan is paused on a channel, the channel number blinks.■ Locking Out a Memory ChannelYou can select Memory channels that you prefer not tomonitor while scanning.1 Press [MR], then rotate the Tuning control to select yourdesired channel.2 Enter Menu mode and access Menu 202.3 Set the lockout to ON to lock the channel out of thescanning sequence.• To cancel lockout, set the lockout to OFF.• The icon appears on the display for a channelthat has been locked out.Note: The L0/U0 to L9/U9 Memory channels cannot be locked out.GROUP SCANFor the purpose of Group Scan, the 1000 Memory channels aredivided into 10 groups, with each group containing 100 channels.Group Scan monitors only the 100 channels which belong to thespecific group you are scanning. The channels are grouped asfollows:MemoryGroupChannelRangeMemoryGroupChannelRange0 0 ~ 99 5 500 ~ 5991 100 ~ 199 6 600 ~ 6992 200 ~ 299 7 700 ~ 7993 300 ~ 399 8 800 ~ 8994 400 ~ 499 9 900 ~ 9991 Press [MR], then rotate the Tuning control to select achannel in your desired group.2 Press the Tuning control (1s).• Scan starts at the current channel.• The 1 MHz decimal blinks while scanning is in progress.• To reverse the scan direction, turn the Tuning control clockwise(upward scan) or counterclockwise (downward scan). You canalso press microphone [UP]/ [DWN].3 To quit Group Scan, press the Tuning control again.Note:◆ At least 2 Memory channels in the selected group must contain data andmust not be locked out of scan.◆ You can also start Memory Scan when in Channel Display mode. WhileScan is paused on a channel, the channel number blinks.■ Memory Group LinkMemory Group Link provides you with the ability to link 2 ormore Memory channel groups together to act as a singlegroup when scanning. You can link up to 10 separate groupstogether, or even add multiple instances of the same groupto the group link, to ensure that one group is scanned moreoften than the other groups.1 Enter Menu mode and access Menu 203.2 Press the Tuning control.• The cursor will begin blinking.3 Rotate the Tuning control to select a group to link.4 Press the Tuning control to set the group and move thecursor to the right.• Press [ ] to move the cursor back or [ ] to move the cursorto the right.5 Repeat steps 3 and 4 to link additional groups together.6 When you have entered your desired groups, press [] to move the cursor to the right, then press the Tuningcontrol to complete the entry and exit Menu mode.• You can insert a character by pressing [INS].• You can delete the selected character by pressing [CLR].• If you have entered the maximum of 6 groups, simply pressthe Tuning control to complete the entry and exit Menu mode.