Kenwood VR-6060 Instruction Manual

Also see for KRF-V8060D: Service manual Service manual Instruction manual Instruction manual

Contents

21 ENSpeaker settingsTo enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (subwoofer, front,center, and surround speakers) as described below.POWERON/STANDBY SETUP MULTI CONTROLPOWER(For KRF-V8060D)RECEIVERSET UPJoystick1Turn on the power to this receiver by pressing the POWERON/OFF and ON/STANDBY ( ) (for VR-6060 only) key orRECEIVER ( ) key.2Press the SETUP key to enter the SET UP mode and pressMMMMM/?????keys for the following displays.1 SP SETUP2 TEST TONE3 SP DISTANCE4 SETUP ENDThe Surround Back and Subwoofer speakers are displayed asfollows:1 6ch AMP SB2 6ch AMP SWUse the MULTI CONTROL knob or Joystick to select the speakers.Press the SETUP key to proceed to the following selection.3Select a speaker system.1 Select the SP SETUP and press the SETUP key again, so thatthe subwoofer setting indication “SUBW ON” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE2 Use the MMMMM/????? keys to select the appropriate settings.1 SUBWOOFER2 FRONT3 CENTER4 SURROUND5 SURROUND BACK6 SW RE-MIX3 Use the MULTI CONTROL knob or Joystick to adjust the sub-woofer setting.1 SUBW ON : Subwoofer setting mode to the receiver isON.2 SUBW OFF : Subwoofer setting mode to the receiver isOFF.• The initial setting is “SUBW ON”.• When the setting “SUBW OFF” is selected, the front speakers areautomatically set to “FRNT LARGE” and the procedure skips tostep 6.• When subwoofer output sound is required, select “FRNT NOR-MAL”.(For VR-6060 only)When you operate on the remote control unit.1 Press the SET UP key repeatedly until “SUBWOOFER” scrollsfrom right to left in the display of the remote control unit.2 Press the Joystick to select “SUBW ON”, then press theENTER key.4 Press the MMMMM/????? keys to accept the setting.• The front speakers setting indication “FRNT” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE5 Use the MULTI CONTROL knob or Joystick to select theappropriate front speakers setting.1 FRNT LARGE : Large front speakers are connectedto the receiver.2 FRNT NORMAL : Average size front speakers are con-nected to the receiver.• For “FRNT LARGE” selection, no sound will be heard fromSUBWOOFER even when it is set to ON. However, if you selectCINEMA EQ when subwoofer is selected, you will be able tohear sound from the subwoofer.When in STEREO mode, the sound goes directly to frontspeaker.6 Press the MMMMM/????? keys to accept the setting.• The center speaker setting indication “CENTER” appears.7 Use the MULTI CONTROL knob or Joystick to select theappropriate center speaker setting.If you selected “LARGE” as the front speakers setting.1 CENTER LARGE : A large center speaker is con-nected to the receiver.2 CENTER NORMAL : An average size center speaker isconnected to the receiver.3 CENTER OFF : Center speaker setting mode tothe receiver is OFF.If you have selected “NORMAL” as the front speakers setting.1 CENTER NORMAL : Center speaker setting mode tothe receiver is ON.2 CENTER OFF : Center speaker setting mode tothe receiver is OFF.Preparing for surround soundContinued to next page•VR609/20-28/EN 10/24/01, 10:36 PM21