Kenwood VRS-6100 Instruction Manual

Also see for VRS-6100: Instruction manual Service manual Service manual

18 ENPreparing for playbackSETUPPOWER ON/STANDBY MULTI CONTROL @/#SETUPMULTICONTROL %/fiPOWERSpeaker settingsTo enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (Subwoofer, Front,Center, Surround and Surround Back speakers) as described below.1Turn on the power to this receiver by pressing the POWERON/STANDBY key (or POWER key).2If you want to use the remote control unit, press the RECEIVERkey on the remote to set it to the receiver control mode.3Initiate the setup mode.1 Press the SETUP key.2 Use the MULTI CONTROL button (or the MULTICONTROL %/fi keys) for the following displays.1 "SP SETUP"2 "TEST TONE"3 "DISTANCE"4 "LFE LEVEL"5 "EXIT"÷ While the main setup display is appeared, the setup modecan be canceled by selecting "EXIT" and then pressing theSETUP key.The flow of the SETUP is as follows;SP SETUP TEST TONE DISTANCE EXITLFE LEVELFront LeftCenterFront RightRight SurroundHTB 1HTB 2HTB 3CustomSubwooferFrontCenterSurroundSurroundBackMANUALAUTOLCRRSLSRBLBSWLCRRSRBLBLSSWSubwooferRe-mixLeft SurroundSurround Back LeftSurround Back Right4Select a speaker system.1 Select "SP SETUP" and press the SETUP key again sothat the speaker system indication "SP SYSTEM"scrolls across the display.s P Y ss T E M2 Use the MULTI CONTROL button (or the MULTICONTROL %/fi keys) to select the speaker systemsetting.1 "HTB 1": Select "HTB 1" if you use speaker system KS-2100HT.2 "HTB 2": Select "HTB 2" if you use speaker system KS-708HT.3 "HTB 3": Select "HTB 3" if you use speaker system KS-908HT.4 "CUSTOM": Select to set up the speakers according tothe speaker system in use. (Speaker setup is requiredevery time after the speaker system is changed.)÷ When the setting "HTB 1", "HTB 2" or "HTB 3" is selected, theprocedure skips to step 5.÷ When you use a KENWOOD speaker system and select"HTB 1", "HTB 2" or "HTB 3" set the speaker setup, the audiowill be corrected automatically according to the speakercharacteristics.÷ When the speaker setting is set to "HTB 1", "HTB 2", "HTB 3 " or"BS OFF" the DOLBY PRO LOGIC IIx, DTS-ES and DOLBYDIGITAL EX listen modes cannot be selected.3 For general speaker setting, use the MULTI CONTROLbutton (or the MULTI CONTROL %/fi keys) to select"CUSTOM", and press the SETUP key again.÷ The subwoofer setting indication "SUBW" appears.s U B W 0 N4 Use the MULTI CONTROL button (or the MULTI CON-TROL %/fi keys) to select the appropriate subwoofersetting.1 SUBW ONWhen a subwoofer is connected.2 SUBW OFFWhen no subwoofer is connected.÷ The initial setting is "SUBW ON".÷ When "SUBW OFF" is selected and the selection isestablished by pressing SETUP key in step 5 below,the front speakers are set automatically to "FRNT LRG"and the procedure jumps to step 8.5 Press the SETUP key to accept the setting.÷ The front speakers setting indication "FRNT" appears.F R N T L R GContinued to next page