Kenwood VRS-6100 Instruction Manual

Also see for VRS-6100: Instruction manual Service manual Service manual

19 ENPreparing for playback6 Use the MULTI CONTROL button (or the MULTICONTROL %/fi keys) to select the appropriatefront speakers setting.1 "FRNT LRG": Large front speakers are connected tothe receiver.2 "FRNT NML": Average size front speakers are con-nected to the receiver.÷ When the subwoofer setting is "SUBW ON", front speak-ers setting is "FRNT LRG" and a stereo source is played,the low frequencies may be reproduced through thefront speakers and no audio output from the subwooferin certain listen modes. In this case, set the subwooferre-mix setting in step $ to "REMIX ON" to output thelow frequencies from the subwoofer.7 Press the SETUP key to accept the setting.÷ The center speaker setting indication "CNTR" appears.8 Use the MULTI CONTROL button (or the MULTICONTROL %/fi keys) to select the appropriatecenter speaker setting.If you selected "FRNT LRG" as the front speakers setting:1 "CNTR LRG": A large center speaker is connected tothe receiver.2 "CNTR NML": An average size center speaker isconnected to the receiver.3 "CNTR OFF" :When no center speaker is connected.If you selected "FRNT NML" as the front speakers setting:1 "CNTR NML": An average size center speaker isconnected to the receiver.2 "CNTR OFF": When no center speaker is connected.9 Press the SETUP key to accept the setting.÷ The surround speaker setting indication "SURR" appears.0 Use the MULTI CONTROL button (or the MULTICONTROL %/fi keys) to select the appropriate sur-round speaker setting.If you have selected "CNTR LRG" as the center speaker setting:1 "SURR LRG":Large surround speakers are connected to the receiver.2 "SURR NML":Average size surround speakers are connected to thereceiver.3 "SURR OFF" :When no surround speakers are connected.If you have selected other than "CNTR LRG" as the centerspeaker setting:1 "SURR NML":Average size surround speakers are connected to thereceiver.2 "SURR OFF":When no surround speakers are connected.÷ When "SURR OFF" is selected and the selection is estab-lished by pressing SETUP in step ! below, the procedurejumps to step $. However, if the subwoofer setting is"SUBW OFF", you can complete the speaker setup andproceed to the speaker volume level adjustment in step 5.! Press the SETUP key to accept the setting.÷ The surround back speaker setting indication "BS" appears.@ Use the MULTI CONTROL button (or the MULTICONTROL %/fi keys) to select appropriate sur-round back speaker setting.If you selected "SURR LRG" as the surround speaker setting :1 "BS LRG":Large surround back speaker is connected to the re-ceiver.2 "BS NML":Average size surround back speaker is connected to thereceiver.3 "BS OFF":When no surround speakers are connected.B s L R GIf you selected "SURR NML" as the surround speakersetting :1 "BS NML" :Average size surround back speaker is connected to thereceiver.2 "BS OFF" :When no surround speakers are connected.# Press the SETUP key to accept the setting.÷ The subwoofer re-mix setting indication "REMIX" appears.$ Use the MULTI CONTROL button (or the MULTICONTROL %/fi keys) to select the appropriatesubwoofer re-mix setting.If "REMIX ON" is selected as the subwoofer re-mix setting,the low frequencies are enhanced by adding the low fre-quencies of other channels to the subwoofer channel oradding the low frequencies of the subwoofer to otherchannels depending on the speaker setup.1 "REMIX ON": Subwoofer re-mix setting mode to thereceiver is ON.2 "REMIX OFF": Subwoofer re-mix setting mode to thereceiver is OFF.÷ If subwoofer is turned "SUBW OFF", subwoofer re-mixsetting is not visible.% Press the SETUP key to accept the setting.