LSC maXim MP Operator's Manual
                                                                                    | |
Contents
| 
maXim MP L(P) XL(P) XXL(P) Advanced Fixture ProgrammingOperator Manual V3LSC Lighting Systems (Aust) Pty. Ltd. Page 53• Get all patched fixtures onto the PatPad.[get], [all]All scans and washes are loaded and hi-lighted• Hi-light only “odd scans”.[group], [f/a] (odd scans).• Apply “red” palette.[palette] [f/a] (red)Odd scans turn red.• Hi-light only “even scans”.[group], [f/a] (even scans)• Apply “blue” palette.[palette], [f/a] (blue)Even scans turn blue.• Hi-light only “odd scans” and “evenscans” groups.Hold [group], tap [f/a] (odd scans), [f/a](even scans).• Apply “drums” preset.[preset], [f/a] (drums)Odd and even scans move to drums, retainingtheir colours.• Hi-light only “even wash” group.[group], [f/a] (even wash)• Apply “floor” preset.[preset], [f/a] (floor)Even wash move to floor.• Apply “blue” palette[palette], [f/a] (blue)Even wash turns blue.• Hi-light only “odd wash” group.[group], [f/a] (odd wash)• Apply “stage” preset.[preset] [f/a] (stage)Odd wash move to stage.• Apply “pink” palette.[palette], [f/a] (pink)Odd wash turn pink.The complete look has been created.• Record the scene.[record scene], [f/a] (scene number).Using the above methods, it is easy to createhundreds of combinations from just a few groups,presets and palettes.16.15 CLONECloning copies selected parameters of thecurrently selected Fixture to another Fixture orgroup of Fixtures. This permits fast duplication oflooks onto multiple Fixtures.To clone a Fixture, select the source Fixture onthe PaTPad and set its parameters. If a filter isapplied then only those parameters that areFiltered are cloned.Only FLASHING parameters will be INCLUDED.To clone the selected Fixture on the PaTPaD to asingle Fixture press;[clone], [f/a] (Fixture Number).To clone the Fixture to a group press;[clone], [group], [f/a] (destination group number).16.16 SAVING SCENESThe maXim provides several ways ofprogramming scenes into memory.• RECORD SCENE, saves the entire output ofthe maXim. What you see is what you get!The method used by the maXim is as follows:Each fixture is checked to see if it has anyintensity on the output. If so, its intensity andall of its parameters are recorded includingintensity fade times. In addition, if a fixture iscurrently on the PaTPad, any parameter timesettings or effects are also recorded.To record a scene of the entire output press;[record scene], [page] (optional red or bluepage), [f/a] (scene number).Note; The maXim will not “RECORD” a scene ifall dimmers/fixtures are at zero intensity level.• STORE, saves only selected (flashing)parameters including time settings or effectsof the Fixtures on the PaTPad. You can selectany parameters by using Filters. You canselect any Fixtures by using Hi-lights.To store a scene of the flashing parameterspress;[store], [page] (optional red or blue page),[f/a] (scene number).• STORE + LEVEL saves fixture parameters,times and effects on the PaTPad as if theSTORE button was pressed but also includesall intensity levels on the output. In addition,fixtures that are not loaded on the PaTPad buthave an intensity above zero have all of theirparameters stored.To store a scene of the flashing parametersincluding levels press;[store + level], [page] (optional red or bluepage), [f/a] (scene number).Record is best used for the fully programmedshow. What you see on stage when the scene isrecorded will be reproduced when the scene isplayed back.Store is best used to create building blocks for the“Ad Lib” show. |
Related manuals for LSC maXim LP
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine