Magnavox 32MV402X Owner's Manual

Also see for 22MV402X: Owner's manual Manual del propietario Manuel du propriétaire

Magnavox 32MV402X Owner's Manual Manual pdf 28 page image

English28Channel installationBe sure the RF cable is correctly connected to this unit and you areregistered with your cable TV provider when you install cable channels.AutoprogramIf you switch wires (e.g. between antenna and CATV) or if you movethe unit to a different area after the initial setting, or if you restore theDTV channels you deleted, it is recommended to use AutoProgram toperform a new channel search.You need to select the signal type in Installation mode before youperform AutoProgram.1 Use ▲▼ to select Channels, then press OK.2 Use ▲▼ to select Autoprogram, then press OK.• If you run Autoprogram when you have locked channels, amessage appears asking to enter your PIN code. Enter yourPIN code in order to complete the installation. You need to setthe channel lock again after the installation.3 Press OK to select Start now.• When the scanning and memorizing are completed, the lowestmemorized channel will be displayed.4 Follow the on-screen instructions to complete the installation.System searching. Please wait...Digital channels found: 0Analog channels found: 0Auto programming may take more than 20 minutes tocomplete.StopNote• After setting Autoprogram, using CH +/− skips unavailable programs automatically.• If you are not receiving a signal from your cable service, contact the cable provider.• If you press or during AutoProgram, the setup of TV channels will be canceled.• Even if Autoprogram is completed, the channel setting will be lost if the AC powercord is unplugged before the unit goes into Standby mode by pressing .• The PIN code will be required once you set a PIN code in the Child and ratings lock.➠ p.25• If you want to change your PIN code, follow the instruction of Change PIN. ➠ p.27Weak channel installationThis function lets you add the channels that were not added by theAutoProgram due to the reception conditions during the initial setup.It is available only when you select Antenna in Installation mode.1 Use ▲▼ to select Channels, then press OK.2 Use ▲▼ to select Weak channel installation, then press OK.• The PIN code will be required if you have locked channels.3 Use ◄► to select channel Input box, then use ▲▼ to select achannel you want to memorize.4 Use ◄► to select Search, then press OK.5 Display will be changed to Store from Search when the channel isfound, then press OK.Note• In most cases, Digital channels are not broadcast on the RF channel on which theyappear on your TV. To add Digital channels you need to know the RF channel on whichthe Digital channel is being broadcast. (e.g. If there is a Digital channel 9.1 which is beingbroadcast on RF channel 25, you need to enter 25 while performing a weak channelinstallation.) To find out the RF channel on which a particular Digital channel is beingbroadcast, please contact your local service provider.Installing Digital channels using Weak channel installation might not work for directcable connections and if the Digital signal is too weak for the TV to process.Installation mode1 Use ▲▼ to select Channels, then press OK.2 Use ▲▼ to select Installation mode, then press OK.3 Use ▲▼ to select Antenna or Cable, then press OK.• When Antenna is selected, the TV detects antenna signals. Itsearches for DTV and Analog TV channels available in your area.• When Cable is selected, the TV detects signals supplied by cable.It searches for DTV Analog TV and Cable channels available inyour area.Uninstall channelsThe channels selected here can be skipped when selecting the channelsusing CH + / −.Those channels can still be selected with the NUMBER buttons.1 Use ▲▼ to select Channels, then press OK.2 Use ▲▼ to select Uninstall channels, then press OK.3 Use ▲▼ to select the channel you want to remove, then press OK.• The removed channels are not displayed on the list of favoritechannels.• To reactivate a removed channel, use ▲▼ then press OK.