Makita DBC260U Original Instruction Manual

Also see for DBC260L: Original instruction manual

Contents

4– Start the Brush Cutter/String Trimmer only in accordance with the instructions.Do not use any other methods to start the engine!– Only use the Brush Cutter/String Trimmer and tools for the specifiedpurposes.– Only start the Brush Cutter/String Trimmer engine after the equipment is fullyassembled. Do not operate the equipment until all of the appropriateaccessories are attached!– Before starting, make sure that the cutting tool is not in contact with hard objectssuch as branches, stones etc. as the cutting tool will rotate when starting.– Switch off the engine immediately if any type of engine problem occurs.– Should the cutting tool hit stones or other hard objects, immediately switch offthe engine and inspect the cutting tool.– Inspect the cutting tool at short regular intervals for damage (inspect forhairline cracks using the tapping test).– Only operate the Brush Cutter/String Trimmer after attaching and adjustingthe shoulder strap to the correct length. The shoulder strap must be adjustedto the user’s size and fastened to prevent fatigue during operation of theequipment. Never hold the cutter with one hand during operation.– During operation, always hold the Brush Cutter/String Trimmer with bothhands.Always ensure you are on safe footing.– Operate the Brush Cutter/String Trimmer in such a manner as to avoidinhalation of the exhaust gases. Never run the engine in an enclosed spacesuch as inside a room (risk of gas poisoning). Carbon monoxide is an odorlessgas.– Always switch off the engine when resting, or if you intend to leave the BrushCutter/String Trimmer unattended, and place it in a safe location to preventinjury to other people and damage to the equipment.– Never put the hot Brush Cutter/String Trimmer onto dry grass or onto anyother combustible materials.– The cutting tool must always be equipped with the appropriate guard.Never run the cutter without this guard!– All protective installations and guards supplied with the equipment must beused during operation.– Never operate the engine if the exhaust muffler is faulty.– Shut off the engine during transport.– When transporting the equipment, always attach the cover to the cuttingblade.– Ensure the Brush Cutter/String Trimmer is positioned safely during transportto avoid fuel leakage.– When transporting the Brush Cutter/String Trimmer, ensure the fuel tank iscompletely empty.– When unloading the Brush Cutter/String Trimmer from a truck or other suchvehicle, never drop the engine to the ground, as doing so may severelydamage the fuel tank.– Unless in an emergency, never drop or cast the Brush Cutter/String Trimmerto the ground as doing so may severely damage the Brush Cutter/StringTrimmer.– Always lift the entire equipment from the ground when moving it. Dragging theequipment on its fuel tank is extremely dangerous and may cause fuel to leak,which may cause fire.– If the equipment gets heavy impact or fall, check the condition beforecontinuing work. Check the fuel system for fuel leakage and the controls andsafety devices for malfunction. If there is any damage or doubt, ask ourauthorized service center for the inspection and repair.Refuelling– Shut off the engine during refuelling, keep away from open flames and do notsmoke during refuelling.– Ensure mineral oil products do not come into contact with skin. Do not inhalethe fuel vapor. Always wear protective gloves during refuelling. Change andclean protective clothing at regular intervals.– To prevent soil contamination (environmental protection), make sure you donot spill fuel or oil on the ground. If you do spill fuel, clean the Brush Cutter/String Trimmer immediately.– Make sure fuel does not come into contact with your clothing. If fuel doescome into contact with your clothing, change your clothing immediately toprevent fire.– Inspect the fuel cap at regular intervals to make sure that it can be securelyfastened and does not leak.– Carefully tighten the fuel tank cap. Once refuelling is complete, move to alocation at least 3 meters away from where you refuelled before starting theengine.• Resting• Transport• Refuelling• Maintenance• Tool Replacement3 meters