Makita DCU180 Instruction Manual

Also see for DCU180: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

18 ENGLISH6. Open the carrier frame toward the front.► Fig.10: 1. Carrier frame7. Unfold the handles, then insert the long hexagonalbolts into the base unit, and then tighten the nuts withthe wrench included in the package.► Fig.11: 1. Long hexagonal bolt8. Tighten the shoulder bolts from the rear using thewrench included in the package.► Fig.12: 1. Shoulder bolt9. Tighten the short hexagonal bolts from both sidesusing the wrench included in the package to fix thehandles.► Fig.13: 1. Short hexagonal boltNOTICE: Do not tighten the short hexagonalbolts with excessive force. Tighten them withproper force so that the handles are stably fixed.NOTICE: Do not pinch the cords with the bolts.10. Fix the cords with the clamps.► Fig.14: 1. Clamp11. Fold the carrier frame.► Fig.15: 1. Carrier frame12. Press the lock button while pulling the brake leverto lock the brake.► Fig.16: 1. Lock button 2. Brake leverCAUTION: If the rear wheels are installed,press the brake pedal for the rear wheel to lockthe rear wheel.13. Hook the carrier lock, and then pull down the locklever to lock the carrier.► Fig.17: 1. Carrier lock 2. Lock leverNOTICE: Make sure that the lock lever is lockedsecurely.NOTICE: Do not pinch the cords with the locklever.NOTE: If you attach the support legs instead of therear wheels, remove the rear wheels from the frames,and then attach the support legs to the frames.► Fig.18: 1. Rear wheel 2. Support legAssembling and installing carrierOptional accessory1. Take out the carrier from the box, attach the siderails to the base frame, and then tighten the thumb nutsto fix the rails.► Fig.19: 1. Thumb nut2. Place the carrier on the base unit, and then insertthe hexagonal bolts and washers into the frames fromthe top. Tighten the washers and spring washers andbutterfly nuts from the bottom to fix the carrier.► Fig.20: 1. Long hexagonal bolt 2. Short hexagonal bolt3. Washer 4. Spring washer 5. Butterfly nutNOTICE: Use the long bolts for the front, and theshort bolts for the rear.Installing bucketOptional accessoryPlace the bucket on the base unit, insert the hexagonalbolts into the frames, and then tighten the washers andspring washers and butterfly nuts from the bottom to fixthe bucket.► Fig.21: 1. Hexagonal bolt 2. Washer 3. Springwasher 4. Butterfly nutFUNCTIONALDESCRIPTIONInstalling or removing batterycartridgeCAUTION: Always switch off the machinebefore installing or removing of the batterycartridge.CAUTION: Make sure that you lock the batterycover before use. Otherwise, mud, dirt, or water maycause damage to the product or the battery cartridge.CAUTION: Always install the battery cartridgefully until the red indicator cannot be seen. If not,it may accidentally fall out of the machine, causinginjury to you or someone around you.CAUTION: Do not install the battery cartridgeforcibly. If the cartridge does not slide in easily, it isnot being inserted correctly.CAUTION: Do not use the high-temperaturebattery cartridge. When the high-temperature bat-tery cartridge is used, the machine stops automati-cally before a short beep sound is emitted, and maycause an injury.Installing the battery cartridge1. Rotate the lock lever, and then open the cover ofthe battery box.► Fig.22: 1. Lock lever 2. Cover2. Align the tongue on the battery cartridge with theslot on the battery box, and then slide the cartridge untilit locks in place with a little click. If you can see the redindicator on the upper side of the button, battery car-tridge is not locked completely.► Fig.23: 1. Battery cartridge3. Insert the lock key in the place shown in the figureas far as it will go.► Fig.24: 1. Lock keyNOTE: If the lock key is not inserted completely, themachine does not work.4. Close the cover of the battery box, and then rotatethe lock lever.► Fig.25: 1. Lock lever 2. Cover