Makita LS0714 Instruction Manual

Also see for LS0714: Instruction manual Instruction manual Instruction manual Parts Breakdown Instruction manual

Contents

56. Turn off tool and wait for saw blade to stopbefore moving workpiece or changing settings.7. Unplug tool before changing blade orservicing.8. Always secure all moving portions beforecarrying the tool.9. Stopper pin which locks the cutter head downis for carrying and storage purposes only andnot for any cutting operations.10. Do not use the tool in the presence offlammable liquids or gases. The electricaloperation of the tool could create an explosion andfire when exposed to flammable liquids or gases.11. Check the blade carefully for cracks ordamage before operation.Replace cracked or damaged bladeimmediately.12. Use only flanges specified for this tool.13. Be careful not to damage the arbor, flanges(especially the installing surface) or bolt.Damage to these parts could result in bladebreakage.14. Make sure that the turn base is properlysecured so it will not move during operation.15. For your safety, remove the chips, small pieces,etc. from the table top before operation.16. Avoid cutting nails. Inspect for and remove allnails from the workpiece before operation.17. Make sure the shaft lock is released before theswitch is turned on.18. Be sure that the blade does not contact theturn base in the lowest position.19. Hold the handle firmly. Be aware that the sawmoves up or down slightly during start-up andstopping.20. Make sure the blade is not contacting theworkpiece before the switch is turned on.21. Before using the tool on an actual workpiece,let it run for a while. Watch for vibration orwobbling that could indicate poor installationor a poorly balanced blade.22. Wait until the blade attains full speed beforecutting.23. Stop operation immediately if you noticeanything abnormal.24. Do not attempt to lock the trigger in the onposition.25. Be alert at all times, especially duringrepetitive, monotonous operations. Do not belulled into a false sense of security. Blades areextremely unforgiving.26. Always use accessories recommended in thismanual. Use of improper accessories such asabrasive wheels may cause an injury.27. Do not use the saw to cut other than wood,aluminum or similar materials.28. Connect miter saws to a dust collecting devicewhen sawing.29. Select saw blades in relation to the material tobe cut.30. Take care when slotting.31. Replace the kerf board when worn.32. Do not use saw blades manufactured fromhigh speed steel.33. Some dust created from operation containschemicals known to cause cancer, birthdefects or other reproductive harm. Someexamples of these chemicals are:• lead from lead-based-painted material and,• arsenic and chromium fromchemically-treated lumber.Your risk from these exposures varies,depending on how often you do this type ofwork. To reduce your exposure to thesechemicals: work in a well ventilated areaand work with approved safety equipment,such as those dust masks that are speciallydesigned to filter out microscopic particles.34. To reduce the emitted noise, always be surethat the blade is sharp and clean.35. The operator is adequately trained in the use,adjustment and operation of the machine.36. Use correctly sharpened saw blades. Observethe maximum speed marked on the saw blade.37. Refrain from removing any cut-offs or otherparts of the workpiece from the cutting areawhilst the tool is running and the saw head isnot in the rest position.38. Use only saw blades recommended by themanufacturer which conform to EN847-1.39. Wear gloves for handling saw blade (sawblades shall be carried in a holder whereverpracticable) and rough material.40. When fitted with laser, no exchange withdifferent type of laser is permitted. Repairsshall only be carried out correctly.SAVE THESE INSTRUCTIONS.

/ 24

Related manuals for Makita LS0714

Makita LS0714 Instruction Manual

This manual is suitable for:

LS0714 LS0714FL LS0714F LS0714L

manualsdatabase

Your AI-powered manual search engine