Makita LS1013 Instruction Manual
Also see for LS1013: Instruction manualInstruction manualParts BreakdownInstruction manualInstruction manual
                                                                            | |
144. Bevel cutLoosen the lever and tilt the saw blade to set thebevel angle (Refer to the previously covered“Adjusting the bevel angle”). Be sure to retightenthe lever firmly to secure the selected bevel anglesafely. Secure the workpiece with a vise. Make surethe carriage is pulled all the way back toward theoperator. Switch on the tool without the blade mak-ing any contact and wait until the blade attains fullspeed. Then gently lower the handle to the fullylowered position while applying pressure in parallelwith the blade and PUSH THE CARRIAGETOWARD THE GUIDE FENCE TO CUT THEWORKPIECE. When the cut is completed, switchoff the tool and WAIT UNTIL THE BLADE HASCOME TO A COMPLETE STOP before returningthe blade to its fully elevated position.CAUTION:• Always be sure that the blade will move down tobevel direction during a bevel cut. Keep hands outof path of saw blade.• During a bevel cut, it may create a conditionwhereby the piece cut off will come to rest againstthe side of the blade. If the blade is raised while theblade is still rotating, this piece may be caught bythe blade, causing fragments to be scattered whichis dangerous. The blade should be raised ONLYafter the blade has come to a complete stop.• When pressing down the handle, apply pressure inparallel with the blade. If a force is appliedperpendicularly to the turn base or if the pressuredirection is changed during a cut, the precision ofthe cut will be impaired.• Always set the sub-fence to the left position whenperforming left bevel cuts.5. Compound cuttingCompound cutting is the process in which a bevelangle is made at the same time in which a miterangle is being cut on a workpiece. Compound cut-ting can be performed at angle shown in the table.When performing compound cutting, refer to “Presscutting”, “Slide cutting”, “Miter cutting” and “Bevelcut” explanations.6. Cutting crown and cove moldingsCrown and cove moldings can be cut on a com-pound miter saw with the moldings laid flat on theturn base.There are two common types of crown moldingsand one type of cove moldings; 52/38° wall anglecrown molding, 45° wall angle crown molding and45° wall angle cove molding. See illustrations.There are crown and cove molding joints which aremade to fit “Inside” 90° corners ((1) and (2) in Fig.A) and “Outside” 90° corners ((3) and (4) in Fig. A).MeasuringMeasure the wall length and adjust workpiece ontable to cut wall contact edge to desired length.Always make sure that cut workpiece length at theback of the workpiece is the same as wall length.Adjust cut length for angle of cut. Always use sev-eral pieces for test cuts to check the saw angles.When cutting crown and cove moldings, set thebevel angle and miter angle as indicated in thetable (A) and position the moldings on the top sur-face of the saw base as indicated in the table (B).001554Miter angle Bevel angleLeft 0˚ - 47˚, Right 0˚ - 45˚ Left and Right 0˚ - 45˚Right 52˚ Left 0˚ - 40˚and Right 0˚ - 45˚0063601. 52/38° typecrown molding2. 45° type crownmolding3. 45° type covemolding1. Inside corner2. Outside corner1. Inside corner2. Outside corner52∞38∞45∞45∞45∞45∞1 2 3001555(1) (2) (3) (4)1 2Fig.A0015562(1)(2)(1)(2)(2)(1)(2)(1)(1)(2)(3)(4)1001557 |
Related manuals for Makita LS1013
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
manualsdatabase
Your AI-powered manual search engine