Makita LS1013 Instruction Manual
Also see for LS1013: Instruction manualInstruction manualParts BreakdownInstruction manualInstruction manual
                        | |
2ENGLISHSPECIFICATIONSModel LS1013 /LS1013F/ LS1013L/LS1013FLBlade diameter 250 mm - 260 mmHole diameterFor all countries other than European countries 25 mm and 25.4 mmFor European countries 30 mmMax. Cutting capacities (H x W) with 260 mm in diameterBevel angleMiter angle 45° (left) 0° 45° (right)0° 50 mm x 310 mm 91 mm x 310 mm 31 mm x 310 mm(left) 50 mm x 200 mm45° (right) 50 mm x 220 mm 91 mm x 220 mm 31 mm x 220 mm52° (right) - 91 mm x 190 mm -No load speed (min -1) 3,700Laser Type (LS1013L/LS1013FL only) Red Laser 650 nm, 1mW ( Laser Class 2 )Dimensions (L x W x H) LS1013/LS1013F…….715 mm x 520 mm x 625 mmLS1013L/LS1013FL …….715 mm x 520 mm x 640 mmNet weight LS1013: 22.4 kg, LS1013F: 22.6 kg, LS1013L: 23.2 kg, LS1013FL: 23.4 kgSafety class /II• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.• Specifications may differ from country to country.• Weight according to EPTA-Procedure 01/2003END216-3SymbolsThe following show the symbols used for the equipment.Be sure that you understand their meaning before use.･ Read instruction manual.･ DOUBLE INSULATION･ To avoid injury from flying debris, keepholding the saw head down, aftermaking cuts, until the blade has cometo a complete stop.･ When performing slide cut, first pullcarriage fully and press down handle,then push carriage toward the guidefence.･ Do not place hand or fingers close tothe blade.･ For your safety, remove the chips, smallpieces, etc. from the table top beforeoperation.･ Always set SUB-FENCE to left positionwhen performing left bevel cuts. Failureto do so may cause serious injury tooperator.･ Always remove SUB-FENCE R whenperforming right bevel cuts. Failure todo so may cause serious injury tooperator.･ Never look into the laser beam. Directlaser beam may injure your eyes.･ Only for EU countriesDo not dispose of electric equipmenttogether with household waste material!In observance of European Directive2002/96/EC on waste electric andelectronic equipment and itsimplementation in accordance withnational law, electric equipment thathave reached the end of their life mustbe collected separately and returned toan environmentally compatiblerecycling facility. ENE006-1Intended useThe tool is intended for accurate straight and mitercutting in wood. With appropriate saw blades, aluminumcan also be sawed. ENF002-1Power supplyThe tool should be connected only to a power supply ofthe same voltage as indicated on the nameplate, andcan only be operated on single-phase AC supply. Theyare double-insulated in accordance with European |
Related manuals for Makita LS1013
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
Makita LS1013 Instruction Manual
manualsdatabase
Your AI-powered manual search engine