MuxLab 500800 Quick Installation Manual

MuxLab 500800 Quick Installation Manual Manual pdf 1 page image

© MuxLab Inc. 94-000972-A SE-000972-A2321Rue Cohen, Montreal, Quebec, Canada. H4R 2N7Tel: (514) 905-0588 Fax: (514) 905-0589Toll Free (North America): (877) 689-5228E-mail: info@muxlab.com URL: www.muxlab.comSpecificationsEnvironment HDMI 2.0Devices Computers and servers with HDMI monitor ports.Transmission Transparent to the userBandwidth (HDMI) 597MHzSignals HDMI 2.0 protocol, HDCP 1.4, HDCP 2.2ConnectorsNote: Cables not included.One (1) HDMI receptacle.One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.Two (2) 3.5mm jacks for audio-in and audio-out (TX)/audio-out and Mic-In ( RX).One (1) 3.5mm jack for directional Infrared port.One (1) DB9 for RS232One (1) 2.1mm locking barrel jack for power.One (1) or Four (4) USB Connector(s) for Host (TX)/Client (RX)Four (4) DIP Switches for device ID addressing.Maximum DistanceBased on a maximum lengthof 6.6ft (2m) of HDMI cableper end.Cat5e/6: 330ft (100m) up to 4K @ 60 Hz (4:4:4)Note: When installed in an electrically noisy environment, an STP cable must beused. Also, cross-connection reduces the effective distance depending on the gradeof twisted cable used.Latency One (1) Frame (16ms), maximum 2 frames (33ms)Compression JPEG 2000Bandwidth Up to 850 MbpsNetwork Requirement 1000BaseT with PoERJ45 Pin ConfigurationReverse Polarity Sensitive.Use EIA/TIA 568A or 586Bstraight-through wiring.RJ45 LinkPin 1 (R) Pin 2 (T)Pin 3 (R) Pin 6 (T)Pin 4 (R) Pin 5 (T)Pin 7 (R) Pin 8 (T)Cable One (1) Cat 5e/6 or better twisted pair cables requiredPower Source This device supports PoE (PD), an external power supply is not included. It isintended to be powered via a PoE (PSE) Ethernet Switch. If required, an optionalpower supply (500993) may be purchased separately.PoE Standard IEEE 802.3afPower Consumption Transmitter: 6Watts Receiver: 8WattsTemperature Operating: 0° to 40°C Storage: -20° to 85°CHumidity: Up to 95% non-condensingDimensions 6.38” x 5.51” x 1.00” (162mm x 140mm x 25mm)Weight 1.5lbs (0.68kg)Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0Warranty 3 yearsOrder Information 500880-TX KVM HDMI over IP PoE Extender TX, 4K/60(UPC: 627699908006)500880-RX KVM HDMI over IP PoE Extender RX, 4K/60(UPC: 627699808009)Accessories(These items are soldseparately)500917 Wall Mount Transceiver Bracket Kit500993 Univ. Locking Power Supply 5VDC/2.6A US/UK/EU BladeKVM HDMI over IP PoE Extender, 4K@60500800Quick Installation GuideOverviewThe KVM HDMI over IP PoE Extender, 4K@60 allows HDMI & USB equipment to be connectedup to 330ft (100m) over an Ethernet LAN, supports HDMI up to 4K @ 60Hz (4:4:4) via Cat5e/6cable in multiple point-to-point and point-to-multipoint configurations. The Transmitter (500800-TX) and Receiver (500800-RX) support PoE (PD) if used with a PoE (PSE) Ethernet Switch.The Transmitter terminates via HDMI, Audio In/Out and USB ports to a computerserver/workstation. The Receiver terminates via HDMI, Audio In/Out, and USB ports to a display,mic & amplified speakers (or headset with mic) respectively, and up to 4 USB devices such as akeyboard, mouse, printer, drawing pad, storage device, camera, etc. A single Receiver can beswitched via hotkey sequences to any Transmitter on the network, allowing a single operator tomanage numerous servers/workstations, in a distributed KVM application.For multiple point-to-point (including point-to-multipoint) configurations the Ethernet Switch mustsupport Gigabit ports, Jumbo Frame capability and DHCP Server capability. MuxLab recommendsusing the Cisco CBS350 Series Managed Switches.The MuxLab ProDigital Network Controller (500812) is available to simplify the configuration andutilization of the 500800 and other MuxLab IP based products via an Ethernet web interface.ApplicationsApplications include management of multi-server systems supporting HDMI displays in ITDepartments within corporations, Educational Institutions, CAD Design, Graphic Design, MediaServers, and Data Centers.Installation1. Identify the connectors on the Transmitter and Receiver as indicated on the product labels, see theabove front and rear product views for further details.2. Verify that the distance between the HDMI Transmitter and Receiver is within MuxLabspecifications (see Specifications table for more details).3. To install the Transmitter:3a. Connect the Transmitter to the computer server/workstation HDMI video source with anHDMI compliant cable.3b. Connect the Transmitter USB Port to the computer server/workstation USB port, using acompliant Type A to Type B USB Cable.

/ 2

Related manuals for MuxLab 500800