Manuals database logo
manualsdatabase
Your AI-powered manual search engine

NBase Communications NH2001M Installation And User Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Page 61 preview
Page 62 preview
Page 63 preview
Page 64 preview
Page 65 preview
Page 66 preview
Page 67 preview
Page 68 preview
Page 69 preview
Page 70 preview
Page 71 preview
Page 72 preview
Contents
  1. user guide
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. Table Of Contents
  6. installation and setup
  7. UG2001SB.QXD 4/12/98 1:53 PM
  11. troubleshooting
  12. technical specifications
  13. NH2001M NBase Communications
  14. OVERVIEW
  15. NETWORK MANAGEMENT SYSTEMS
  16. ACCESSING THE SNMP AGENT
  17. Configuring the SNMP Agent
  18. Setting the IP Address
  19. Testing the Installation
  20. Features
  21. Command Line Interface Command Structure
  22. Console Commands
  23. logout
  24. set-attr-text
  25. System Commands
  26. set-stst-level
  27. set-sw-file
  28. set-fg-param
  29. IP Commands
  30. get-ip-cfg
  31. clear-ip-cfg
  32. get-arp-tbl
  33. ping
  34. ping-stop
  35. SNMP Commands
  36. SNMP Trap Message Commands 3
  37. add-trap
  38. Switching Database Commands
  39. Learning Table
  40. get-lt-16
  41. find-lt-addr
  42. del-lt-entry
  43. add-lt-entry
  44. Port Monitoring
  45. Port Configuration Commands
  46. set-speed-sel
  47. Switching Statistics Commands
  48. get-colls-cnt
  49. get-mgm-brcnt
  50. Spanning Tree Commands
  51. set-br-prio
  52. set-prt-prio
  53. Command Line Reference
  54. port monitoring commands
  55. USING AN SNMP MANAGER
  56. IP Setup
  57. SNMP Setup
  58. TROUBLESHOOTING
  59. APPENDIX A - SOFTWARE DOWNLOADING
  60. APPENDIX B - SYSTEM DEFAULT VALUES
NBase Communications NH2001M Installation And User Manual Manual pdf 39 page image
31NH 2001MNBase CommunicationsIP CommandsThis section lists the IP Configuration commands available to the commandline interface. It is separated into different sections to allow simpler lookup: IPConfiguration lists general configuration commands, Ping lists commands per-taining to the ping ability of the Agent, Address Resolution Protocol listsARP-related information.IP Configurationget-ipThis command shows the device’s current IP address, if any.SYS_console> get-ip -- no IP Config definedThe device has no IP Address definedSYS_console> _SYS_console> get-ip -- IP Config already definedThe device IP address is: 129.001.001.064SYS_console> _set-ipUsage:set-ipSets the IP address of the SNMP Agent. If no IP address was previously set(as is the default factory configuration), the new value will be used immedi-ately and saved into NVRAM. Otherwise the new value will only be stored inthe NVRAM, and the user must execute a “warm-reset” to effect the change.AI2001SB.QXD 4/5/98 11:27 AM Page 31
/ 72
This manual is suitable for:
NH2001M
Manuals database logo
manualsdatabase
Your AI-powered manual search engine