NEC 42 VP5 VM5 Operation Manual

Also see for PlasmaSync 42XM3: Supplementary guide Installation guide Supplementary guide Brochure Brochure

Contents

NEC 42 VP5 VM5 Operation Manual Manual pdf 21 page image

21Option1 Settings MenuSetting the on-screen menuThis sets the position of the menu, the display format(horizontal or vertical) etc.Example: Turning the DISPLAY OSM offOn “OPTION1” menu, select “OSM”, then press the MENU/ENTER button.The “OSM” menu appears.On “DISPLAY OSM” of “OSM” menu, select “OFF”.OSMEXITDISPLAY OSMOSM ADJ.OSM ANGLEOSM ORBITEROSM CONTRAST: OFF: 1: H: OFF: LOWSEL. RETURNADJ.Information DISPLAY OSM settingsON: The on-screen menu appears.OFF: The on-screen menu does not appear.If you press the DISPLAY button on the remote controlfor more than 3 seconds the main menu will appearand can be set (although it is not ON). OSM ADJUST settingsAdjusts the position of the menu when it appears onthe screen.The position can be set between 1 to 6. OSM ANGLE settingsSets the display format (landscape “H” or portrait “V”).When the unit is installed vertically set the OSMANGLE at “V”.“H” “V” OSM ORBITER settingsON: The position of the menu will be shifted by eightdots each time OSM is displayed.OFF: OSM will be displayed at the same position. OSM CONTRAST settingsNORMAL: OSM brightness is set to normal.LOW: OSM brightness is set to lower.Setting the BNC connectorsSelect whether to set the input of the 5 BNC connectors toRGB and component.Example: Set the BNC INPUT mode to “COMP.”On “BNC INPUT” of “OPTION1” menu, select “COMP.”.OPTION1 1 / 3EXITOSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETNEXT PAGE: COMP.: RGB: AUTO: 1080B: OFF: OFFSEL. RETURNADJ.Information BNC INPUT SettingsRGB: Use the 5BNC terminals for RGB input.COMP.: Use the 3BNC terminals for component input.Checking the signal being transmitted toRGB1 terminalUse this to confirm the signal being transmitted to theRGB1 terminal.It is set to RGB and can not be adjusted.OPTION1 1 / 3OSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETNEXT PAGECAN NOT ADJUST: RGB: RGB: AUTO: 1080B: OFF: OFFSetting a computer image to the correct RGBselect screenWith the computer image, select the RGB Select modefor a moving image such as (video) mode, wide mode ordigital broadcast.Example: Setting the “RGB SELECT” mode to“MOTION ”On “RGB SELECT” of “OPTION1” menu, select“MOTION”.OPTION1 1 / 3EXITOSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETNEXT PAGE: RGB: RGB: MOTION: 1080B: OFF: OFFSEL. RETURNADJ.Information RGB SELECT modesOne of these 6 modes must be selected in order todisplay the following signals correctly.AUTO: Select the suitable mode for the specificationsof input signals as listed in the table “Computer inputsignals supported by this system” on page 7 of ModelInformation.STILL: To display VESA standard signals. (Use thismode for a still image from a computer.)MOTION: The video signal (from a scan converter)will be converted to RGB signals to make the picturemore easily viewable. (Use this mode for a motionimage from a computer.)OPTION1 1 / 3EXITOSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESETNEXT PAGE: RGB: RGB: AUTO: 1080B: OFF: OFFSEL. RETURNMENU/ENTER OKOPTION1EXITOSMBNC INPUTD-SUB INPUTRGB SELECTHD SELECTINPUT SKIPALL RESET: RGB: RGB: AUTO: 1080B: OFF: OFF1024768SEL.RETURNMENU/ENTER OK