NEC MultiSync LCD175VXM+ User Manual

Also see for LCD175VXM - MultiSync - 17" LCD Monitor: User manual Specifications Specifications User manual User manual

Contents

English-1EnglishDeclaration of the ManufacturerWe hereby certify that the colour monitors MultiSync LCD175VXM+(L174F1)/LCD195VXM+ (L194F2) are in compliance withCouncil Directive 73/23/EEC:– EN 60950-1Council Directive 89/336/EEC:– EN 55022– EN 61000-3-2– EN 61000-3-3– EN 55024RISK OF ELECTRIC SHOCK • DO NOT OPENTO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’SPOLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIEDSERVICE PERSONNEL.WARNINGCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICINGTO QUALIFIED SERVICE PERSONNEL.This symbol warns user that uninsulated voltagewithin the unit may have sufficient magnitude to causeelectric shock. Therefore, it is dangerous to make anykind of contact with any part inside this unit.This symbol alerts the user that important literatureconcerning the operation and maintenance of thisunit has been included. Therefore, it should be readcarefully in order to avoid any problems.CAUTIONand marked withNEC Display Solutions, Ltd.4-13-23, Shibaura,Minato-KuTokyo 108-0023, JapanContentsYour new NEC MultiSync LCD monitor box* should contain thefollowing:• MultiSync LCD monitor with tilt base• Audio Cable• Power Cord• Video Signal Cable (15-pin mini D-SUB male to 15-pin miniD-SUB male)• Video Signal Cable (DVI-D to DVI-D) (LCD195VXM+ only)• User’s Manual• CD-ROM• Cable management cover*Remember to save your original box and packing material to transport or shipthe monitor.User’sManualAudioCablePowerCord15-pin mini D-SUBmale to 15-pin miniD-SUB maleDVI-D to DVI-D(LCD195VXM+only) MultiSync LCD monitorCD-ROMQuick StartTo pull the stand, follow these instructions:1. Place monitor face down on a non-abrasive surface (Figure 1).2. Pull the stand holding the monitor with the other hand until thestand clicks (Figure 2).NOTE: Handle with care when pulling the stand.NOTE: Reverse this procedure if you need to re-pack the monitor.To attach the MultiSync LCD monitor to your system, follow theseinstructions:1. Turn off the power to your computer.2. For the PC or MAC with DVI digital output: Connect the DVI-Dsignal cable to the connector of the display card in your system(Figure A.1). Tighten all screws.For the PC with Analog output: Connect the 15-pin mini D-SUBsignal cable to the connector of the display card in your system(Figure A.2). Tighten all screws.For the Mac: Connect the MultiSync Macintosh cable adapter(not included) to the computer. Attach the 15-pin miniD-SUB signal cable to the MultiSync Macintosh cable adapter(Figure A.3). Tighten all screws.NOTE: Some Macintosh systems do not require a Macintosh cableadapter.3. To attach the Cable management cover:Insert the tabs of the Cable management cover into the holes ofStand neck and slide the Cable management cover downward intoplace (Figure A.4).NOTE: Please confirm that the tabs are completely secure.4. Connect all cables to the appropriate connector on the back of themonitor (Figure B.1). Connect the Headphone (not included) tothe appropriate connector at the rear side of the monitor (FigureC.1).Figure A.1 Figure A.2Macintosh Cable Adapter (not included)Cable managementcoverFigure 1 Figure 2Figure A.3BaseStandCable management coverFigure A.4AUDIO INPUTD-Sub (Input1)DVI-D (Input2)Cable management coverConnect to Computeraudio outputFigure B.101_English 10/1/07, 1:06 PM1