NEC MultiSync UN462A User Manual

Also see for MultiSync UN462A: Installation guide Installation guide Firmware update procedure User manual

Contents

NEC MultiSync UN462A User Manual Manual pdf 114 page image

English−110SCHEDULE MENUOFF TIMER Set the monitor to power off after a preset time period. A time period between 1 to 24 hours may be set.NOTE: [SCHEDULE] is not available if [OFF TIMER] is [ON].RESET Resets all SCHEDULE options back to factory setting, except for [DATE & TIME] and [DAYLIGHT SAVING].MULTI-INPUTMULTI-INPUT MENUKEEP MULTI PICTUREMODE*1Allows the monitor to remain in [MULTI PICTURE] and [TEXT TICKER] mode after powering off.When Power is returned, [MULTI PICTURE] and [TEXT TICKER] appear without having to enter the OSD.MULTI PICTURE MODE*1, *3 Sets multi picture mode.MULTI PICTURE When [OFF] is selected, one picture is displayed.When [ON] is selected, several pictures are displayed. Select [PIP] or [PBP].NOTE: When [ON] is selected, [TEXT TICKER], [CLOSED CAPTION], [TILE MATRIX], [MOTION] in [SCREENSAVER], [IMAGE FLIP] except for [NONE], [SUPER] in [INPUT CHANGE] is released.ACTIVE PICTURE*1, *2ACTIVE When [MULTI PICTURE] is [OFF], [PICTURE 1] is the active picture. When [MULTI PICTURE] is [ON], selectan active picture from several pictures.NOTE: This function depends on [MULTI PICTURE] setting.ACTIVE FRAME The active picture is shown within a red frame.INPUT SELECT*3, *5 Selects the Multi Picture input. Press the + button or - button to select the input.NOTE: • This function is not available when [MULTI PICTURE] is [OFF].• When changing input signal for the active picture, after selecting an input press SET/POINTZOOM button.PICTURE1PICTURE2PICTURE SIZE*1, *2, *4 Sets the Active Picture size.Press the SET/POINT ZOOM button to adjust the picture size. Press + button or CH/ZOOM+ button to expand.Press - button or CH/ZOOM- button to reduce.PICTURE POSITION*1, *2, *4 Sets the Active Picture location.Pressing the + button moves the Active Picture to the right, and pressing the - button moves it to the left.Pressing the  button moves the Active Picture up, and pressing the  button moves it down.PICTURE ASPECT*1, *2, *4 Selects the Active Picture frame aspect.To change aspect ratio of the screen image, see page 35.TEXT TICKER*1, *3 Shows a cropped portion of [PICTURE2] either horizontally or vertically over the image of PICTURE1.This can be used to display, for example, a text ticker application.The Text Ticker portion of the [PICTURE2] source that is displayed will be the top (horizontal) or left side(vertical).NOTE: • When [TEXT TICKER] is set, [MULTI PICTURE MODE] and [STILL] are not available.• [TEXT TICKER] is released if following menu is activated: [MULTI PICTURE MODE],[TILE MATRIX], [SCREEN SAVER], [IMAGE FLIP], [SUPER] in [INPUT CHANGE],[CLOSED CAPTION].• When this function is active, [POINT ZOOM] and [STILL] are not available.MODE Enables Text Ticker and allows you to set Horizontal or Vertical direction.POSITION Selects the location of the Text Ticker on the screen.SIZE Determines the size of the Text Ticker in relationship to the overall screen size.DETECT Enables auto-detection of the Text Ticker.INPUT SELECT Set input signal for [PICTURE1], [PICTURE2].*1: This function is released when selecting [SUPER] in [INPUT CHANGE], [MOTION] in [SCREEN SAVER], [TILE MATRIX] and [IMAGE FLIP] except for [NONE].*2: When [TEXT TICKER] is active or multi picture is [OFF], this function is not available.*3: When you select [OPTION] for input, this function depends on which Option Board installed in the monitor.*4: This function is not available if [PIP] is set at [MULTI PICTURE MODE] and then [PICTURE1] is set at [ACTIVE PICTURE].*5: This function is released when selecting [SUPER] in [INPUT CHANGE] or [TEXT TICKER] is active.