NightStick XPP-5454GC Instruction Manual

Also see for XPP-5454GC: Instruction manual Instruction manual

NightStick XPP-5454GC Instruction Manual Manual pdf 1 page image

Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.comINS-XPP-5454GC-LG-22 09-08-2022Instruction ManualXPP-5454GCUS PATENT 9,713,217THE XPP-5454GC IS APPROVED FOR USECLASS I DIV 1 GRPS A-D T3CLASS II & III GRPS E-G T135ºCCLASS I ZONE 0 AEx ia IIC T3 GaEx ia IIC T3 GaII 1 G Ex ia op is IIC T3 GaEx ia op is IIC T3 GaIntertek ITS 13 ATEX27928XITS21UKEX0266XIECEx ITS 18.0030X-20ºC ≤ Tamb ≤ +40ºC1.5V/Cell E92 or EN922575ID 5012927INTRINSICALLY SAFESECURITE INTRINSEQUEBayco Products, Inc. XPP-5454GC640 S. Sanden Blvd., Wylie, TX 75098Ex ia op is IIC T3 Ga(-20ºC ≤ Tamb ≤ +40ºC)NCC 15.0296 X0359WARNINGS - INTRINSICALLY SAFEy Warning: Use only the approved non-rechargeable batteries listed below.y Warning: Do NOT attempt to use rechargeable AAA batteries with this light.y Warning: To prevent ignition of a hazardous atmosphere, do not open the batterycompartment in the hazardous environment. This task must ONLY be performed in anarea known to be non-hazardous.y Warning: When exchanging batteries, use only ENERGIZER E92 or EN92BATTERIES.y Warning: To prevent ignition of a hazardous atmosphere, the AAA batteries mustonly be exchanged in an area known to be non-hazardous.y Warning: To reduce the risk of explosion, do not mix new non-rechargeable batterieswith used non-rechargeable batteries, or mix non-rechargeable batteries from differentmanufacturers.y Warning: Substitution of components may impair intrinsic safety.SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETYy For personal safety, always confirm the rating of any known hazardous or potentiallyhazardous location where the light is to be used.BATTERY INSTALLATIONWARNING: In order to maintain the XPP-5454’s Intrinsically Safe rating, the onlyAAA batteries certified for use with this light are the ENERGIZER E92 or EN92BATTERIES.y Do not attempt to use any other brand or model of AAA batteries with this light.y Do not attempt to use any type of rechargeable AAA batteries with this light.Warning: To prevent ignition of a hazardous atmosphere, do not open the batterycompartment door in the hazardous environment. This task must ONLY be donein an area known to be non-hazardous.y Loosen the locking screw located on the back of the battery compartment door.NOTE: Do NOT attempt to completely remove the locking screw. Doing so is notnecessary and may damage the threads. The screw simply needs to be loosenedenough to allow the battery compartment door to open.y Using 3 – AAA ENERGIZER E92 or EN92 BATTERIES (make sure that all 3batteries are of the same model), install the batteries in the back of the light payingclose attention to the markings inside the battery compartment for proper batteryterminal polarity alignment.y Close the battery compartment door.y Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so may damage thethreads and impact the light’s Intrinsic Safety.OPERATIONTHE XPP-5454GC HAS TWO BUTTONS THAT CONTROL LIGHT OUTPUT:LIGHTING MODESPressing the Spotlight Button will turn on the spotlight. Pressing the FloodlightButton will turn on the floodlight. Pressing both buttons will turn on both the Spotlightand the Floodlight. This mode is called Dual-Light.EACH BUTTON HAS TWO BRIGHTNESS SETTINGSy High-brightness - Press the desired button oncey Low-brightness - Press the desired button a second timey Pressing the same button a third time will turn that lighting mode offTHE XPP-5454GC HAS A TILT ADJUSTMENT FEATURE:Simply adjust the tilt angle of the light to illuminate the desired area.THE XPP-5454GC FITS ON ANY HARD HAT THAT HAS A HARD HAT LAMPBRACKET ATTACHED:NIGHTSTICK NS-HMC4 HEADLAMP BRACKET MOUNTING INSTRUCTIONSy Ensure mounting surface is clean and oil-free (use alcohol wipe if needed)y Prior to installing, determine mounting location that allows headlamp to fully tiltwithout interfering with helmet brim.y Remove adhesive backing.y Firmly press bracket into place up for 30 seconds with flat side facing up (see image).y While supporting mount, slide headlamp clip into bracket slot. (Note: adhesivereaches peak strength in 24 hours)TO ATTACH TO THE HARD HAT LAMP BRACKETSlide the clip on the back of the XPP-5454GC into the slot on the top edge of theHard Hat Lamp Bracket and press down firmly until the clip is fully engaged into thebracket.TO REMOVE FROM THE HARD HAT LAMP BRACKETGrasp the XPP-5454GC and pull up until the clip slides out of the Hard Hat LampBracket.XPP-5454GC