Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- GENERAL INFORMATION
- SAFETY
- TECHNICAL DATA (For BA 451, BA 451D, BA 531, BA 531D)
- DIMENSIONS CA 551
- MAINTENANCE
- MACHINE NOMENCLATURE (For BA 451, BA 451D, BA 531, BA 531D)
- MACHINE NOMENCLATURE (For BA 551, BA 551D, BA 551CD, BA 611D)
- MACHINE NOMENCLATURE (For CA 451, CA 531)
- MACHINE NOMENCLATURE (For CA 551)
- SOLUTION/CLEAN WATER SUPPLY SYSTEM
- SOLUTION FILTER CLEANING (For BA 551, BA 551D, BA 551CD, BA 611D, CA
- SOLENOID VALVE DISASSEMBLY/ASSEMBLY (For BA 451, BA 451D, BA
- SOLENOID VALVE DISASSEMBLY/ASSEMBLY (For BA 551, BA 551D, BA 551CD BA 611D, CA 551)
- TROUBLESHOOTING
- ECOFLEX™ SYSTEM
- CLEAN WATER FILTER CLEANING (For BA 551D, BA 551CD, BA 611D)
- DETERGENT TANK CLEANING (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- ECOFLEX™ SYSTEM DRAINING (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- WATER PUMP DISASSEMBLY/ASSEMBLY (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- DETERGENT PUMP AND CHECK VALVE DISASSEMBLY/ASSEMBLY (For BA 451D, BA 531D)
- DETERGENT PUMP AND CHECK VALVE DISASSEMBLY/ASSEMBLY (For BA 551D BA 551CD, BA 611D)
- BRUSHING SYSTEM
- BRUSH/PAD-HOLDER DECK DISASSEMBLY/ASSEMBLY (For CA 451, CA 531, CA 551)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For BA 451, BA 451D, BA 531, BA 531D)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For BA 551, BA 551D)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For BA 551CD)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For BA 611D)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For CA 451, CA 531, CA 551)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (For BA 551, BA 551D)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (For BA 551CD)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (For BA 611D)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (For BA 551CD)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (For BA 611D)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (For CA 451, CA 531, CA 551)
- CHECK/REPLACEMENT/ADJUSTMENT OF DRIVING BELTS FROM MOTORS TO CYLINDRICAL BRUSHES (For BA 551CD)
- RECOVERY WATER SYSTEM
- SQUEEGEE CLEANING/CHECK/REPLACEMENT AND SQUEEGEE BLADE REPLACEMENT (All models)
- VACUUM SYSTEM MOTOR FILTER CLEANING (All models)
- VACUUM SYSTEM MOTOR ELECTRICAL INPUT CHECK (For CA 451, CA 531, CA 551)
- VACUUM SYSTEM MOTOR CARBON BRUSH CHECK/REPLACEMENT (All models)
- VACUUM SYSTEM MOTOR DISASSEMBLY/ASSEMBLY (All models)
- SQUEEGEE SPRING CHECK/REPLACEMENT (All models, with aluminium squeegee)
- DRIVE SYSTEM
- DRIVE SYSTEM ELECTRONIC BOARD DIAGNOSTIC TABLE
- OTHER SYSTEMS
- ELECTRICAL SYSTEM
- BATTERY DISASSEMBLY/ASSEMBLY (For BA 451, BA 451D; BA 531, BA 531D BA 551, BA 551D, BA 551CD, BA 611D)
- BATTERY TYPE SETTING (WET OR GEL) (For BA 451, BA 531, BA 551)
- BATTERY TYPE SETTING (WET OR GEL) (For BA 451D, BA 531D, BA 551D BA 551CD, BA 611D)
- FUSE CHECK/REPLACEMENT (For BA 451, BA 451D, BA 531, BA 531D, BA
- FUSE CHECK/REPLACEMENT (For CA 431, CA 531, CA 551)
- COMPONENT LAYOUT (For BA 451, BA 531, BA 551)
- WIRING DIAGRAM (For BA 451, BA 531, BA 551)
- COMPONENT LAYOUT (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- WIRING DIAGRAM (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- COMPONENT LAYOUT (For CA 451, CA 531, CA 551)
- WIRING DIAGRAM (For CA 451, CA 531, CA 551)
|
ELECTRICAL SYSTEMENGLISH SERVICE MANUAL98 909 6756 000(5)2010-03 BA 451 / BA 451D / BA 531 / BA 531D / BA 551 / BA 551D / BA 551CD / BA 611DCA 451 / CA 531 / CA 551BATTERY TYPE SETTING (WET OR GEL) (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)Set the electronic board of the machine and of the battery charger (if equipped) according to the type of batteries installed (WET orGEL) as shown below:Machine settingTurn the ignition key (80) to “I” position and pay attention to the following in the very first seconds of machine operation:1.If the green warning led (81a) is flashing, the machine is set to GEL.•If the red warning led (81c) is flashing, the machine is set to WET.•If the setting is to be changed, perform the following procedure.2.Turn off the machine by turning the ignition key (80) to “0”.3.Press and hold the switches (71) and (73) at the same time, then turn the ignition key (80) to “I”.4.Release the switches (71) and (73) at least 8 seconds after starting the machine.5.Within three seconds, press the switch (73) again for a few seconds and check that the warning led for the required setting is6.flashing (as shown in step 1).Battery charger setting (if equipped)Remove the battery charger data inspection window screws (A).7.Remove the window (B).8.Turn the battery charger selector (C) to WET position for lead batteries, or to GEL position for gel batteries.9.Install the window (B) and tighten the screws (A).10.CAABS301567 PreviousNext |