Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- GENERAL INFORMATION
- SAFETY
- TECHNICAL DATA (For BA 451, BA 451D, BA 531, BA 531D)
- DIMENSIONS CA 551
- MAINTENANCE
- MACHINE NOMENCLATURE (For BA 451, BA 451D, BA 531, BA 531D)
- MACHINE NOMENCLATURE (For BA 551, BA 551D, BA 551CD, BA 611D)
- MACHINE NOMENCLATURE (For CA 451, CA 531)
- MACHINE NOMENCLATURE (For CA 551)
- SOLUTION/CLEAN WATER SUPPLY SYSTEM
- SOLUTION FILTER CLEANING (For BA 551, BA 551D, BA 551CD, BA 611D, CA
- SOLENOID VALVE DISASSEMBLY/ASSEMBLY (For BA 451, BA 451D, BA
- SOLENOID VALVE DISASSEMBLY/ASSEMBLY (For BA 551, BA 551D, BA 551CD BA 611D, CA 551)
- TROUBLESHOOTING
- ECOFLEX™ SYSTEM
- CLEAN WATER FILTER CLEANING (For BA 551D, BA 551CD, BA 611D)
- DETERGENT TANK CLEANING (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- ECOFLEX™ SYSTEM DRAINING (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- WATER PUMP DISASSEMBLY/ASSEMBLY (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- DETERGENT PUMP AND CHECK VALVE DISASSEMBLY/ASSEMBLY (For BA 451D, BA 531D)
- DETERGENT PUMP AND CHECK VALVE DISASSEMBLY/ASSEMBLY (For BA 551D BA 551CD, BA 611D)
- BRUSHING SYSTEM
- BRUSH/PAD-HOLDER DECK DISASSEMBLY/ASSEMBLY (For CA 451, CA 531, CA 551)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For BA 451, BA 451D, BA 531, BA 531D)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For BA 551, BA 551D)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For BA 551CD)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For BA 611D)
- BRUSH MOTOR ELECTRICAL INPUT CHECK (For CA 451, CA 531, CA 551)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (For BA 551, BA 551D)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (For BA 551CD)
- BRUSH MOTOR CARBON BRUSH CHECK/REPLACEMENT (For BA 611D)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (For BA 551CD)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (For BA 611D)
- BRUSH MOTOR DISASSEMBLY/ASSEMBLY (For CA 451, CA 531, CA 551)
- CHECK/REPLACEMENT/ADJUSTMENT OF DRIVING BELTS FROM MOTORS TO CYLINDRICAL BRUSHES (For BA 551CD)
- RECOVERY WATER SYSTEM
- SQUEEGEE CLEANING/CHECK/REPLACEMENT AND SQUEEGEE BLADE REPLACEMENT (All models)
- VACUUM SYSTEM MOTOR FILTER CLEANING (All models)
- VACUUM SYSTEM MOTOR ELECTRICAL INPUT CHECK (For CA 451, CA 531, CA 551)
- VACUUM SYSTEM MOTOR CARBON BRUSH CHECK/REPLACEMENT (All models)
- VACUUM SYSTEM MOTOR DISASSEMBLY/ASSEMBLY (All models)
- SQUEEGEE SPRING CHECK/REPLACEMENT (All models, with aluminium squeegee)
- DRIVE SYSTEM
- DRIVE SYSTEM ELECTRONIC BOARD DIAGNOSTIC TABLE
- OTHER SYSTEMS
- ELECTRICAL SYSTEM
- BATTERY DISASSEMBLY/ASSEMBLY (For BA 451, BA 451D; BA 531, BA 531D BA 551, BA 551D, BA 551CD, BA 611D)
- BATTERY TYPE SETTING (WET OR GEL) (For BA 451, BA 531, BA 551)
- BATTERY TYPE SETTING (WET OR GEL) (For BA 451D, BA 531D, BA 551D BA 551CD, BA 611D)
- FUSE CHECK/REPLACEMENT (For BA 451, BA 451D, BA 531, BA 531D, BA
- FUSE CHECK/REPLACEMENT (For CA 431, CA 531, CA 551)
- COMPONENT LAYOUT (For BA 451, BA 531, BA 551)
- WIRING DIAGRAM (For BA 451, BA 531, BA 551)
- COMPONENT LAYOUT (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- WIRING DIAGRAM (For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D)
- COMPONENT LAYOUT (For CA 451, CA 531, CA 551)
- WIRING DIAGRAM (For CA 451, CA 531, CA 551)
|
BRUSHING SYSTEMSERVICE MANUAL ENGLISHBA 451 / BA 451D / BA 531 / BA 531D / BA 551 / BA 551D / BA 551CD / BA 611DCA 451 / CA 531 / CA 551 909 6756 000(5)2010-03 55BRUSH MOTOR ELECTRICAL INPUT CHECK (For CA 451, CA 531, CA 551)WARNING!This procedure must be performed by qualified personnel only.CheckRemove the brush, as shown in the User Manual.1.Disconnect the power supply cable (59) from the electrical mains but do not place it on the holder (60).2.If the power supply cable (59) is on the holder (60), remove it.3.Move aside the recovery water drain hose (16).4.Remove the mounting screws (A) of the panel (C).5.Loosen the mounting screws (B) of the panel (C).6.Carefully move backwards the upper end (D) of the panel (C).7.Apply the amperometric pliers (E) on one cable (F) (connection symbols: “F4” or “F5”) of the brush motor.8.Connect the power supply cable (59) to the electrical mains.9.Turn on the brush by pressing the switch (62) and check that the motor electrical input is 3 - 4 A at 230 V. Turn off the brush by10.pressing the switch (62).Disconnect the power supply cable (59) from the electrical mains.Remove the amperometric pliers (E).If the electrical input is higher, perform the following procedures to detect and correct the abnormal input:Check if there is dust or dirt (ropes, cables, etc.) on the brush hub.•Check the motor carbon brushes (see the procedure in the relevant paragraph).•If the above-mentioned procedures do not lead to a correct electrical input, the motor must be replaced (see the procedure inthe relevant paragraph).ResetPerform steps 3 to 7 in the reverse order.11. PreviousNext |