Nivus OCM PRO CF Instruction Manual

Also see for OCM PRO CF: Instruction manual

Contents

Nivus OCM PRO CF Instruction Manual Manual pdf 162 page image

®Instruction ManualOCM Pro CFPage 162 OCM Pro CF - Rev. 07 as of 04.12.201214 EmergencyIn case of emergency- press the emergency-off button of the main system or- set the slide switch (see Fig. 6-33 Position of slide switch ) on the unit toOFF.15 Dismantling/DisposalThe device shall be disposed according to the local regulations for electronicproducts.16 Table of PicturesFig. 2-1 Overview enclosure ............................................................................................................................. 8Fig. 2-2 Overview sensors and electronic box ................................................................................................. 9Fig. 3-1 OCM Pro CF nameplate .................................................................................................................... 13Fig. 4-1 Possible combinations OCP type S4 ................................................................................................ 16Fig. 4-2 Possible combinations OCP type M4 ................................................................................................ 16Fig. 4-3 Combi sensor type POA with pressure measurement cell................................................................ 17Fig. 4-4 Combi sensor type CS2 with pressure measurement cell ................................................................ 17Fig. 4-5 Flow velocity sensor, type CSM ........................................................................................................ 18Fig. 4-6 Situation at first signal reception ....................................................................................................... 19Fig. 4-7 Situation at second signal detection.................................................................................................. 20Fig. 4-8 Echo signal images and evaluation................................................................................................... 20Fig. 4-9 Investigated flow profile ..................................................................................................................... 20Fig. 4-10 Computed 3-dimensional flow profile ................................................................................................ 21Fig. 4-11 Type key for OCM Pro CF measurement transmitters...................................................................... 22Fig. 6-1 Wall mount enclosure ........................................................................................................................ 26Fig. 6-2 Wiring diagram OCM Pro CF wall mount enclosure ......................................................................... 28Fig. 6-3 Connecting a flow velocity or water-ultrasonic combi sensor on the OCM Pro type S4W0 / M4W0 29Fig. 6-4 Connecting a second velocity sensor to the OCM Pro type M4W0 .................................................. 29Fig. 6-5 Connecting a third velocity sensor to the OCM Pro type M4W0....................................................... 29Fig. 6-6 Connection electronic box Type EBM with water-ultrasonic sensor Type CSM and air-ultrasonicsensor Type DSM to Type S4W0 / M4W0 ........................................................................................ 30Fig. 6-7 Connection 2. electronic box Type EBM with water-ultrasonic sensor Type CSM to Type M4W0 .. 30Fig. 6-8 Connection 3. electronic box Type EBM with water-ultrasonic sensor Type CSM to Type M4W0 .. 30Fig. 6-9 Connecting a flow velocity sensor with integrated pressure measurement cell to type W0 ............. 31Fig. 6-10 Connecting the air-ultrasonic sensor type LUS to type M4W0 / S4W0 ........................................... 31Fig. 6-11 Connecting a 2-wire sensor (EX for level measurement................................................................... 31Fig. 6-12 Connecting a 2-wire sensor for level measurement to type W0 ....................................................... 32Fig. 6-13 Connecting external level measurement from NivuMaster to type W0 ............................................. 32Fig. 6-14 Wall mount enclosure - connecting the overvoltage protection for power supply and analog inputsand outputs ........................................................................................................................................ 34Fig. 6-15 Overvoltage protection water-ultrasonic sensor or electronic box, wall mount enclosure ................ 35Fig. 6-16 Overvoltage protection air-ultrasonic sensor, type OCL, wall mount enclosure ............................... 35Fig. 6-17 Panel mount enclosure ..................................................................................................................... 36Fig. 6-18 Wiring diagram OCM Pro CF panel mount enclosure....................................................................... 37Fig. 6-19 Connecting a flow velocity or water-ultrasonic combi sensor to the OCM Pro CF,type S4F0 / M4F0 .............................................................................................................................. 38Fig. 6-20 Connecting a second flow velocity sensor to type M4F0 .................................................................. 38Fig. 6-21 Connecting a third flow velocity sensor to type M4F0....................................................................... 38Fig. 6-22 Connection electronic box Type EBM with water-ultrasonic sensor Type CSM and air-ultrasonicsensor Type DSM to Type S4F0 / M4F0 .......................................................................................... 39Fig. 6-23 Connection 2. electronic box Type EBM with water-ultrasonic sensor Type CSM to Type M4F0 ... 39