Encore Automatic PE Powder Spray Gun26Part 1612502−01  2018 Nordson CorporationReplacing the Power Supply1. Remove the nozzle and electrode support assembly as described onpage 12. If using a conical nozzle, always remove the deflector cap anddeflector first.2. Remove the hose adapter and powder tube as described on page 25.3. See Figure 16. Unscrew and remove the two Philips head screws (31)and internal-toothed lock washers (32) from the end cap (28).4. Carefully separate the end cap/rear body assembly (27, 28) from thefront body assembly.3132282724Harness ConnectorsReceptacle Lock Nut16AFigure 16 Gun Disassembly − Powder Tube Replacement16A. Filter assembly24. Receptacle harness27. Rear body28. End cap31. Screws32. Lock washers5. Insert a small flat-bladed screwdriver into the slot on the harnessconnectors and separate the receptacle harness (24) from the powersupply harness.6. See Figure 17. Disconnect the clear air wash tubing from the barbedfitting (23) inside the rear body.7. If replacing the cable receptacle, barbed fitting, or rear gun body:a. See Figure 17. Use a 4-mm hex wrench to remove the hex headscrew (25) and washer (26) land disconnect the ground terminal.b. Use a 1/4-in. deep well socket to unscrew the barbed fitting.Remove it and the lock washer from the end cap.c. See Figure 16. Unscrew the lock nut from the receptacle, thenremove the receptacle and harness from the end cap.d. If replacing the rear gun body, separate the rear gun body from theend cap. Install the end cap on a a new rear gun body.e. Discard the nut that is included with the new barbed fitting, then withthe lock washer installed on the fitting, install it through the rear gunbody and thread it into the end cap. Tighten the fitting securely.

Safety Qualified Personnel 1

Personal Safety

Grounding

Dimensions and Weights

Installation Standard Articulated Bar Mount Kit 7

Optional Articulated and Fixed Gun Bar Mount Kits

Gun Connections

Optional Ion Collector Installation

Changing From Conical to Flat or Corner Spray Nozzle

Cleaning Flat and Corner Spray Nozzles

daily maintenance

Weekly Maintenance

Nordson Corporation

Electrode Support Resistance Test

Cable Continuity Tests

Standard Gun Cables

Replacing the Powder Tube

Replacing the Power Supply

Electrode Support Sleeve Replacement XD Version

Electrode Support Sleeve Replacement SD Version

Parts Spray Gun 32

Electrode Support Assemblies

Cables

Optional Flat and Corner Spray Nozzles

Standard Articulating Gun Bar

Optional Articulating Gun Bar

Optional Fixed Gun Bar

Optional Ion Collector Kit

Nordson Encore PE Product Manual

Encore PE

Safety

System Setup

System Connections

System Setup and Connections

Spray Gun Connections

Air Tubing and Powder Hose

Pump and Hopper Connections

Connecting the Powder Hose to the Pump

Mobile Systems

System Electrical Connections

Entering Configuration Mode

Function Settings

Description

Mobile System Components

Equipment Labels

Operation

Displays and LEDs

Custom Electrostatic Mode

Classic AFC Mode

Powder Flow Settings

Smart Flow Mode Settings

Classic Flow Mode Settings

Spray Gun Operation

Purging

Maintenance

Daily Maintenance

troubleshooting

General Troubleshooting Chart

Spray Gun Power Supply Resistance Test

Gun Cable Continuity Test

Repair

Power Supply Replacement

Powder Path Installation

Gun Reassembly

Cable Replacement

Cable Installation

Switch Installation

Electrode Support Assembly Replacement − XD Version

Electrode Support Assembly Replacement − SD Version

Controller Repair

Rear Panel Components

System Part Numbers

Spray Gun

Spray Gun Options

Controller Parts

Front Panel and Internal Cabinet Ground Parts List

Rear Panel Parts Illustration

Rear Panel Parts List

Manifold Illustration and Parts List

System Components and Parts

System Options

Wiring Diagram

ENCORE PE-HD