Notifier AFP-3030 Operation Manual

Also see for AFP-3030: Programming manual Installation manual Operation manual Installation manual

Contents

Notifier AFP-3030 Operation Manual Manual pdf 19 page image

AFP-3030 Operations Manual — P/N DOC-01-033:C 05/12/2018 19System or Point Fault Event Operation of the Control Panel• Displays FAULT in the upper left corner of the panel display and, if a point fault, the type of fault and information specific to thedevice. (A system and a point fault message are shown in the figures below)• Sends a Fault message to the history buffer, installed printer and annunciatorsWhen an unacknowledged event with a higher priority exists, the control panel retains the indications of the higher priority event (themessage, lit LED, audible tone, etc.) while activating the Fault relay, illuminating the SYSTEM FAULT or FAULT LED, and sending a Faultmessage to the history buffer, installed printer and annunciators.A system fault message is shown in Figure 2.3, and a point fault is shown in Figure 2.4. Refer to Section 1.4.2, “Event Reporting For-mat”, on page 9 for identification of each message field.Figure 2.3 Sample Message for System FaultFigure 2.4 Sample Message for Point Fault2.3.2 How to Respond to a System or Point FaultIf the control panel indicates a fault, the operator can do the following:1. Press the SILENCE BUZZER key to silence the panel sounder.The control panel sends an acknowledge message to the History buffer, installed printers and annunciators.2. Check the fault message for an indication of the fault.• Refer to Table 2.1 or Table 2.2 below for point and system fault explanations, if necessary.• Press the MORE INFO soft key to display the MORE INFORMATION screen and view additional information onthe device and possibly preprogrammed text for recommended action. (Refer to Figure 1.9 on page 14 for anexample of the this screen and an explanation of its fields.)3. Correct the condition causing the fault. If the fault clears, the control panel sends a Clear Fault message to the History buffer,installed printers and annunciators.If all faults clear and no supervisory signals or fire alarms exist, the control panel does the following:• Returns to Normal operation (indicated by the “System Normal” message)• Sends a “System Normal” message to the panel display, History buffer, installed printers and annunciators• Restores faults automatically - even if faults are not acknowledgedF A U L T : 3 O F 5A C K N O W L E D G E D F A U L T A C M P S IP S I E X T F L T M O N I T O R1 0 : 0 3 : 2 3 A T U E 2 2 , J A N , 2 0 1 9 A C M 0 1 P 3 0M O R E I N F O . . .1 F L T L 0 1 M 0 0 1M o d u l e L 0 1 M 0 0 12 F L T L 0 1 M 0 0 2M o d u l e L 0 1 M 0 0 23 F L T P S I E X T F L T M O N I T O RA L M : 0 S U P : 0 F L T : 5 D I S : 0 O T H E R : 01 1 : 5 8 : 4 3 A T U E 2 2 , J A N , 2 0 1 9F A U L T : 1 O F 5A C K N O W L E D G E F A U L T N O A N S W E RZ 0 0 1 : Z o n e Z 0 0 1 M O N I T O RM o d u l e L 0 1 M 0 0 11 0 : 3 5 : 1 7 A T U E 2 2 J A N 2 0 1 9 L 0 1 M 0 0 1M O R E I N F O .1 F L T L 0 1 M 0 0 1M o d u l e L 0 1 M 0 0 12 F L T L 0 1 M 0 0 2M o d u l e L 0 1 M 0 0 23 F L T P S I E X T F L T M O N I T O RA L M : 0 S U P : 0 F L T : 5 D I S : 0 O T H E R : 01 1 : 5 8 : 4 3 A T U E 2 2 , J A N , 2 0 1 9