14Part Names and Functions (continued)Rear Panel1. DC OUT 24 V connectorDC 24 V is output while this unit is operating with the ACpower supply.This will supply DC power supply to the camera adapter.24 V is not output when this unit is operating with theDC power supply.2. CA IN connectorConnect the BNC cable from the camera adapter.Connect with the BS OUT connector of the cameraadapter using the BNC cable (5C-FW).3. CA OUT connectorConnect the BNC cable from the camera adapter.Connect with the BS IN connector of the cameraadapter using the BNC cable (5C-FW).4. GENLOCK IN connectorThis is a reference signal input connector to lock thisunit with an external sync.Select the signal to input that matches the video formatof the camera recorder. For details, refer to [About theSignals to Input to GENLOCK IN Connector] (page 16).5. GENLOCK LOOPOUT connectorThis is a loop through with the GENLOCK IN connector.6. VIDEO OUT (MENU) connectorComposite signal is output.Color phase will be also locked to the reference signalwhen the BS signal (burst sync) is input as a referencesignal into the GENLOCK IN connector.The down convert signal is not output from the VIDEOOUT (MENU) connector when the video format for thecamera recorder is set to 1080-23.98PsF, 1080-24PsFor 720-60P.25IRE NTSC signal is output to display menu.7. RET IN VIDEO signal connectorThis is an input connector for the return video signalfrom this unit to the camera adapter.This will input a composite signal.RET video cannot be viewed on the CRT viewfinder orcolor viewfinder when the video format is set to23.98PsF or 1080-24PsF.When the system frequency is 59.94 Hz, be sure tomatch the SETUP menu settings of the camera and thisunit to the SETUP level of the signal input to the RET INVIDEO connector.8. RET IN SDI signal connectorThis is an input connector for the return video signalfrom this unit to the camera adapter.This will input a SDI signal.RET video cannot be viewed on the CRT viewfinder orcolor viewfinder when the video format for the camerarecorder is set to 1080-23.98PsF or 1080-24PsF.For signals supplied to the 7.RET IN VIDEO signalconnector and the 8.RET IN SDI signal connector andthe signal output from the camera adapter, refer to[About the RET Signal] (page 16).9. SDI OUT 1 connectorThis will output the SDI signal that was output from thecamera recorder.10. SDI OUT 2 connectorThis will output the SDI signal that was output from thecamera recorder.Same signal as the signal output from SDI OUT 1connector is output.11. INCOM/TALLY connectorThis is a connector between this unit and the externalintercom system and TALLY system.12. TALLY selection switchThis is a switch to match with the TALLY systemconnected to the 11.INCOM/TALLY connector.Select either contact or supplied voltage. For suppliedvoltage: It is compatible with 8 V - 12 V.MAKE: Select this when the TALLY input signal is acontactV: Select this when the TALLY input signal is asupplied voltage13. INCOM selection switchThis is a switch to match with the INCOM systemconnected to the INCOM/TALLY connector.Select either 4-wire format or RTS format.4W: Select this when it is a 4-wire formatRTS: Select this when it is a RTS formatz Set this switch to 4 W if the INCOM is not used and it isa system with this unit and a camera adapterconnected one-to-one.z Make sure to connect to a RTS system when theswitch is set to RTS. When using the RTS format, the11.INCOM/TALLY connector should be terminated with200 h between pin 7 and pin 8 (refer to page 22).DC OUT 24VCAOUTINGEN LOCK RET INVIDEO OUTLOOP OUTINSDI OUTINCOM/TALLYREMOTE DC IN 12V AC INTALLYMAKE 4WINCOMRETSDIVIDEOV RTS21VIDEO(MENU) SDI1 2431 2 3 4 5 6 7 8 9 10 11 121314 15 16 1817
