Panasonic AG-HPG10P Operating Instructions Manual

Also see for AG-HPG10E: Parts list

Contents

Panasonic AG-HPG10P Operating Instructions Manual Manual pdf 85 page image

85 For yourreferenceMenuWarning system tableWhen trouble is detected immediately after the power is turned on or during operation, the user is alertedby the power lamp and beep sound (provided that “ON” is selected as the “BEEP SOUND” setting on the“OTHER FUNCTIONS” screen (Page 82)).Priority Type ofwarningLCD monitor screendisplay Power lamp Beep sound Warning description andrecord/playback operation Action to be taken1 System errorSYSTEM ERRORCause displayed∗1 ,blinks in red.Blinks at arate of 4 timesper second.Beepscontinuously.P2 microprocessor orcontrol trouble. Operationis stopped.Check the causedisplay∗1 , and consultyour vendor.2P2 cardejectiontroubleTURN POWER OFFBlinks in red.Blinks at arate of 4 timesper second.Beepscontinuously.Trouble has occurred in theinternal memory because aP2 card was ejected whileits data was being accessed.Both access LEDs blink inorange (4 Hz).Turn off the power.If something is wrongwith the clips on theejected P2 card, repairthem.3 Low batterychargeLOW BATTERYBlinks in red. Blinks withthe remaining batterydisplay empty. (Thisdisplay appears evenwhen it has been set toOFF on the setting menu.)Blinks at arate of onceper second.Beepscontinuously.The battery charge is low.Recording or playbackstops. If the voltage fallsfurther, the power isautomatically turned off.Replace the battery.4 P2 card fullP2 FULLBlinks in red (displayappears only for 3seconds when [REC] ispressed).Blinks ata rate of 4times persecond uponcompletion ofrecording.Beepscontinuouslyuponcompletion ofrecording.There is no more freememory left on the P2card. Recording isstopped∗3 .Delete the unnecessaryclips or insert a newcard.5 RecordingtroubleREC WARNINGCause displayed∗2 ,blinks in red.Blinks at arate of 4 timesper second.Beepsintermittentlyat a rate of4 times persecond.Recording trouble.Recording is stopped∗4 .Turn off the power and turnit back on. Then checkthe recording/playback.Replace the P2 cardif recording cannot beperformed properly.6Connectionerror in PCmode at1394 HOST.NoneBlinks at arate of 4 timesper second.NoneThe 1394 cable has beendisconnected or a multiplenumber of units have beenconnected. (Ordinary PCmode operations can beperformed.)Connect the hard driveas specified in theprocedure concerned.7Near lowbatterychargeOne block on theremaining batterydisplay is blinking. (Thisdisplay appears evenwhen it has been setto OFF on the settingmenu.)Blinks at arate of onceper second.NoneThe battery charge isfalling to low. Operation iscontinued.Replace the battery asnecessary.8 P2 cardnearly fullRemaining mediamemory display blinks.Blinks at arate of once asecond duringrecording.NoneUnder 2 minutes ofmemory remaining onthe P2 card (remainingmemory display showsless than one minute).This warning appears onlyduring recording.Replace the P2 cardor add another card asnecessary.∗1 P2 SYSTEM ERROR Cause display• P2 MICON ERROR: P2 microprocessor does not respond.• P2 CONTROL ERROR: Trouble has occurred in the P2 recording control.• REC RAM OVERFLOW: Recording RAM overflow∗2 REC WARNING Cause display• CARD ERROR∗: P2 card trouble (slot number of trouble card is displayed in ∗)• REC RAM OVERFLOW: Recording RAM overflow• ERROR: Other recording trouble∗3 The warning is cleared when any one of the following operations is performed.• When a playback function button (STOP, PLAY, STILL, FF or REW) is pressed• When the PC mode is selected while [THUMBNAIL/MODE] is held down for more than 2 seconds• When a P2 card has been ejected or another card has been inserted∗4 The warning is cleared when any one of the following operations is performed.• When a playback function button (STOP, PLAY, STILL, FF or REW) is pressed• When a P2 card has been ejected