Panasonic CY-VHD9401N Operating Instructions Manual

Also see for CY-VHD9401N: Installation instructions Installation instructions

Panasonic CY-VHD9401N Operating Instructions Manual Manual pdf 4 page image

6 CY-VHD9401NENGLISHCY-VHD9401N 7ENGLISHSafety Information (continued)Observe the following cautions when handlingthe batteries for the remote control unit.Proper Use of the Batteries≥ Remote control unit: Lithium battery (CR2025/1F)≥ IR Wireless Headphones: Manganese R03, AAA,UM-4 dry cells≥ Improper use of batteries may causeoverheating, an explosion or ignition, resultingin injury or a fi re. Battery leakage may damagethe product.≥ Do not mix old and new batteries. (IR WirelessHeadphones)≥ Do not use alkaline dry cells or rechargeabletype batteries. (There is the danger of liquidleakage.)≥ Do not recharge, disassemble, deform or heatthe batteries. Do not put them in fire or water.Do not place them in contact with metal objects.≥ Do not leave the battery or the remote controlunit containing the battery in places where thetemperature is extremely high (such as insidecars with all the windows closed, or inside the cartrunk, places where the sun shines directly on it, ornear the heater). Such misuse/abuse can cause thebatteries to burst, rupture, leak or overheat causingfi re and damage to property or injury.≥ Only use the specified batteries.≥ Insert the batteries with the + and - ends asshown on the battery case.≥ Immediately replace used up batteries.≥ When not using the remote control unit for along period of time, remove the battery.≥ Insulate the batteries when disposing of orstoring them. (Put them in a plastic bag or wrapthem with tape or something.)≥ Obey local ordinances when disposing of thebatteries.What to do if a battery has leaked (R03, AAA,UM-4 dry cells)≥ Carefully wipe up all the electrolyte on thebattery case, and then replace the leaking batterywith a new one.≥ If your body or clothing has made contact withthe electrolyte, wash it off thoroughly with water.≥ If some of the electrolyte should fi nd its wayinto your eyes, do not rub them but immediatelywash them with water, and consult a doctor.Caution Observe the following cautions whenusing this unit or installing.q If an RCA or similar cord is to be connected tothe product, adjust its position and length so thatit will not become entangled or come into contactwith your body. After use, be absolutely sure todisconnect it from the product.Failure to heed this caution may result in anaccident and/or injury.q Before connecting the product with anotherdevice, consult the operating instructionsof the device concerned to ensure that theproduct and device will be connected properly.Incorrect connections may cause accidentsand/or malfunctioning.Observe the following cautions whenreplacing the bulb of the dome light.≥ Have the dome light replaced by a qualifi edspecialist.≥ While you are replacing a bulb, be absolutelysure to keep the dome light switch at OFF.Otherwise, you may burn yourself.≥ The bulb is very hot to touch while it is lightedand immediately after it has gone off.≥ Before attempting to replace it, turn the domelight switch off, wait several minutes and thencheck that it cooled off.≥ Use a bulb with the specified ratings (12 V/5 W).Do not use any other bulb.≥ Gripping the bulb with too much force maybreak it. Wear fi ngerstalls or use some otheranti-slip method when replacing it.Observe the following cautions wheninstalling.q Do not damage the cords.Wire breaks and short circuits can causeelectrical shock or fire.Run the cords so that they do not get tangled inthe moving parts (such as the seat rails), screwsor car body.Do not damage, pull too hard, fold, twist, orwork on the cords. Do not place the cords nearheating appliances or put heavy objects on thecords.q Install the monitor in a position where it willnot hit anybody’s head when it opens andcloses.Failure to heed this caution may result in anaccident and/or injury.q Take care not to injure your fingers with thepower drill or other tool you are using. Alsotake care not to damage the wiring near theceiling panel.Failure to heed this caution may result in anaccident, injury and/or malfunctioning.q Do not poke your fingers between the ceilingand this product.Failure to heed this caution may result in aninjury and/or malfunctioning of the product.q Wear gloves for installation work to protectyourself from injuries.Failure to heed this caution may result in anaccident and/or injury.q Take care that the wiring is not pinched orcaught by the base plate attached to the roofor any other parts.Failure to heed this caution may result in anaccident and/or injury.q Before installing the unit, be absolutely sure tocheck that the screws do not make any contactwith the ceiling panel.If some space is required between the base plate andthe unit, attach and adjust the under cover. For detailson installing the under cover, consult your dealer.q Wear goggles or protective eyewear to shieldyour eyes from airborne metal particles duringdrilling.Failure to heed this caution may result in anaccident and/or injury.q As you cut the headliner, take care not to cutyour fi ngers. Also take care not to damage anyother areas of the headliner.Failure to heed this caution may result in anaccident and/or injury.q When fi tting the product, using the suppliedbase plate, please ensure that it is properlysecured to avoid excessive vibration or thechance of the product coming loose andcausing an accident.q The metal plate, screws and nuts required toattach the base plate are not supplied.The parts required for attaching the productdiffer depending on the vehicle type. Consult aprofessional technician for more details, andalways have a professional technician wireand install the product for you.q Follow local rules and regulations forinstalling the unit.Observe the following cautions forconnections.≥ To prevent damage to the unit, be sure to followthe connection diagram.≥ Do not connect the power connector to the unituntil the wiring is completed.≥ When connecting stripped wires, be sure to wrapthem securely with electrical tape to prevent shorts.≥ Bundle all cables and keep cable terminals freefrom touching any metal parts.Observe the following cautions forinstalling the base plate≥ Do not install the base plate as fi gure on page38 of Installation Instructions.One method for installing the main unit is touse bond or adhesive tape (option) to fix woodor plastic (option) to the ceiling panel beforeattaching the base plate. However, the main unitwill not be securely installed using this method,and the bond may separate due to heat fromthe vehicle. Shock, impact, vibration or mainunit weight in this situation would be extremelydangerous.≥ The main unit weighs approximately 3 k . Beabsolutely sure that the main unit is securedproperly and does not come loose even withvibration or shock.≥ Check that there is suffi cient strength in theceiling reinforcement crosspieces to hold theweight of the product.≥ Check the thickness of the interior materials,attachment space, etc, refer to the attachmentexample (installation instructions) and determinethe base plate attachment position.≥ Take care that the base plate or attachmentscrews do not pinch cords and wiring. Also takecare not to scratch or damage the ceiling orother parts of the vehicle.