Panasonic DMP-BD50 Operating Instructions Manual

Also see for DMP-BD50: Operating instructions Operating instructions

Contents

ENGLISH33RQT9185Card PageNetworkOther difficulties with playbackWhen other Panasonic products respond to this remote controlChange the remote control code on the main unit and the remote control (the two must match) if you place other Panasonic products closetogether.The capacity of the SD carddecreased.≥When a BD-Video that supports the virtual package is used, and an SD card is in the slot,data may be written to the SD card. Erase the data by using “BD-Video Data Erase”, formatthe card or use a new card.16MPEG-2 motion pictures andmusic on an SD card cannot beplayed.≥Data that can be played from an SD card are AVCHD and JPEG data. 5The contents of the cardcannot be read.≥The card is not compatible or the contents on the card may be damaged.≥Turn off and then turn on the unit again.5—I can’t connect to the network. ≥Has the LAN cable come unplugged? Check that the LAN cable is properly connected.≥Have you plugged in a modular cable for use with a telephone into the LAN terminal on thisunit? Connect with a straight LAN cable.≥Is the power for the modem or broadband router turned on? Turn the power on for eachdevice.≥Is there a mistake in the network settings? Follow any instructions you may have receivedfrom your ISP (Internet Service Provider) and make changes to the settings.≥Are the broadband router settings correct? Read the operating instructions for the broadbandrouter.≥Is the broadband router and/or modem correctly connected? Check the operatinginstructions for each device and connect accordingly.≥Check the “Network Settings” and “BD-Live Internet Access” settings.99————26, 28While using my PC, I cannotconnect to the network.≥Does your Internet Service Provider (ISP) or service contract prevent multiple terminalsconnecting at the same time? Check the content of your contract.—Audio and video momentarilypause.≥This occurs between playlist chapters or scenes ([AVCHD]).≥When playing a title recorded on both layers, the unit automatically switches between layersand plays the title in the same way as a normal program. However, video and audio maymomentarily cut out when the unit is switching layers.——BD-Video or DVD-Video is notplayed.≥Ensure the disc is for the correct BD-Video region code or DVD-Video region number, and isnot defective.≥You have set a ratings level to limit BD-Video or DVD-Video play. Change this setting.≥Some BD-Video can only be output with HDMI.Cover26—Picture-in-picture is not playedwith BD-Video.≥Confirm whether the disc supports picture-in-picture. —The virtual package is notplayed with BD-Video.≥Confirm whether the disc supports the virtual package.≥The inserted SD card does not have sufficient available capacity.≥The SD card is write-protected.≥Sub contents copied to an SD card are provided by the disc producer as a part of theBD-Video content. Even if you record images and audio onto an SD card, it cannot be playedas a virtual package.16—516Alternative soundtrack andsubtitles cannot be selected.≥The languages are not recorded on the disc.≥You may not be able to use the on-screen menu to change the soundtrack and subtitles onsome discs. Use the disc’s menus to make changes.—14No subtitles. ≥Subtitles are not recorded on the disc.≥Turn the subtitles on. Set “Subtitle” on the on-screen menu to “On”.—24Angle cannot be changed. ≥Angles can only be changed during scenes where different angles are recorded. —The resume play function doesnot work.≥Memorized positions are canceled when– pressing [∫] several times.– opening the disc tray.≥The resume play function may not work depending on the disc.≥[BD-V]: On BD-Video discs including BD-J, the resume play function does not work.———1 Press [SETUP].2 Press [3, 4] to select “General” and press [OK].3 Press [3, 4] to select “Remote Control” andpress [OK].4 Press [3, 4] to select the code (1, 2, or 3) andpress [OK].5 To change the code on the remote controlWhile pressing [OK], press and hold thenumbered button ([1], [2] or [3]) for more than5 seconds.6 Press [OK].NOTEWhen the following indicatorappears on the unit’s display andyou are unable to operate the unitThe unit’s remote control codePress and hold [OK] and theindicated number button at the sametime for more than 5 seconds.Set Code 1Set Code 2Set Code 3Remote ControlPress [] and [OK ] togetherfor more than 5 seconds onthe remote.D.R33