Panasonic DMP-BD50 Operating Instructions Manual

Also see for DMP-BD50: Operating instructions Operating instructions

Contents

34RQT9185MessagesThe following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup anduse.On the television PageAuthorisation Error.This unit is not authorised toplay this title.≥You are trying to play the DivX VOD content that was purchased with a differentregistration code. You cannot play the content on this unit. 20Cannot play. ≥You inserted an incompatible disc. 4, 5Cannot play on this unit. ≥You tried to play a non-compatible image.≥Confirm “SD” on the unit’s display is not blinking and re-insert the card.5, 22—No disc is inserted. ≥The disc may be upside down. —Rental Expired. ≥The DivX VOD content has zero remaining plays. You cannot play it. 20$ This operation is currentlydisabled.≥The operation is prohibited by the unit or disc. —Cannot connect.Please check the connection ofthe LAN cable.≥When a hub is used but its Link lamp does not light up, check the cable connection, LANterminal connection, cable itself (a cross cable may be used by mistake), etc. 9IP address is not set. ≥The “IP Address” in “IP Address / DNS Settings” is “---. ---. ---. ---“. Set the “IP Address”,“Subnet Mask”, and “Gateway Address“. (Select the automatic address acquisition ifnecessary.)12Cannot obtain IP address.Please check the connection orsetting of the router.≥If you use a hub, then check the connection between the hub and the router.– Use the UPLINK port of the hub to connect to a router.– Check whether or not the hub’s Link lamp lights up. If it does not light up, then check thecable connection, LAN terminal connection, cable itself (a cross cable may be used bymistake), etc.≥If the above conditions are OK, then the router may not operate in DHCP mode. Check therouter settings and operation. You may reset the router to restore it to normal.99This IP address is already inuse.Please check the setting.≥This unit’s IP address is used by another device. Check the IP addresses of this unit,personal computers, and routers, etc. If necessary, reconfigure them to avoid IP addressesfrom being duplicated.—Connection test could not beconducted.≥Turn the unit off. Remove the power cord and reconnect it and try again. If the samesymptom persists, then consult your dealer. —IP address was not setcorrectly.Connection Test wasunsuccessful. No reply fromGateway. Please check theconnection or setting of therouter.≥If you use a hub, then check the connection between the hub and the router.– Use the UPLINK port of the hub to connect to a router.– If the hub’s Link lamp does not light up, then check the cable connection, LAN terminalconnection, cable itself (a cross cable may be used by mistake), etc.≥Check the “IP Address”, “Subnet Mask”, and “Gateway Address” in the “IP Address / DNSSettings”.≥If the MAC address information is required, then press [SETUP] to display the “NetworkSettings” menu.91212Network connection wasrejected.Please confirm Setup “BD-LiveInternet Access”.≥When you set “BD-Live Internet Access” to “Limit” and play BD-Live contents which do nothave a content owner certificate, the Internet access of the content is not allowed. If youallow the content to connect to Internet, set “BD-Live Internet Access” to “Permit”.26On the unit’s displayF99 ≥The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to standbyfor 3 seconds. Now press [Í/I] on the main unit again to turn the unit on.—HDMI ONLY ≥Some BD-Video discs can only be output with HDMI. —No PLAY ≥There is a viewing restriction on a BD-Video or DVD-Video. 26No READ ≥The disc is dirty or badly scratched. The unit cannot play. —PLEASE WAIT ≥Displayed when the unit is started and turned off. This is not a malfunction.≥The unit is carrying out its recovery process. You cannot operate the unit while “PLEASEWAIT” is displayed.——SET (“  ” stands for a number.)≥The remote control and main unit are using different codes. Change the code on theremote control.Press and hold [OK] and the indicated number button at the sametime for more than 5 seconds.33UNFORMAT ≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL orDVD-RW (DVD-Video format).—UNSUPPORT ≥You have inserted a disc the unit cannot play. 4, 5U59 ≥The unit is hot.The unit switches to standby for safety reasons. Wait for about 30 minutes until themessage disappears.Select a position with good ventilation when installing the unit. Do not block the cooling fanon the rear of the unit.—U72U73≥The HDMI connection acts unusually.– The connected equipment is not HDMI compatible.– Please use HDMI cables that have the HDMI logo (as shown on the cover).– The HDMI cable is damaged.—D.R34