Panasonic DMP-BD50 Operating Instructions Manual

Also see for DMP-BD50: Operating instructions Operating instructions

Contents

28RQT9184(ENG)“TV/Device Connection”TV AspectSet to match the type of television connected.When connected to a 4:3 aspect television:4:3 Pan & Scan: Video recorded for a widescreen is played as Pan & Scan(unless prohibited by the producer of the disc). When playingBD-Video, video is output as “4:3 Letterbox”.4:3 Letterbox: Video recorded for a widescreen is played in the letterboxstyle.When connected to a 16:9 widescreen television:16:9: Video recorded for 4:3 aspect screen is displayed as a 4:3ratio image in the center of the screen.16:9 Full: Video recorded for 4:3 aspect screen is displayed as ahorizontally stretched 16:9 image.HDMI ConnectionPress [OK] to show the following settings.HDMI Video ModeSelect “On” when video is output from HDMI AV OUTterminal.On: Images are output from the HDMI terminal in the resolution set in “HDMIResolution”. Video from COMPONENT VIDEO OUT terminal is output as“480i”.Off Images are output in the resolution set in “Component Video Resolution”.HDMI ResolutionThe items supported by the connected devices areindicated on the screen as “”. When any item without“” is selected, the images may be distorted.Auto: Automatically selects the output resolution best suited to theconnected television (1080p, 1080i, 720p or 480p).480p 720p1080i 1080p– When the unit is connected to an amplifier/receiver that does not support theresolution set on the unit, the video cannot be output properly. In this case, usethe HDMI cable to connect the unit to the TV and then connect the unit to theamplifier/receiver using a cable other than HDMI.– To enjoy high definition video up-converted to 1080p, you need to connect theunit directly to 1080p compatible HDTV (High Definition Television). If this unit isconnected to an HDTV through other equipment, it must also be 1080pcompatible.24p Output [BD-V] [DVD-V]When this unit is connected to a TV supporting 1080/24poutput via an HDMI cable, this unit displays each frame at1/24 second intervals – the same interval originally shotwith the film camera.When playing DVD-Video, set to “On” and then set “24p”in “Video” ( 25) to “On”On: Images in 24p are output in 24p as they are.However,–when video is being output at 24 frames, images from any otherterminal than the HDMI terminal may not be output properly.–[BD-V]: when images other than 24p are played, images are output at60p.OffHDMI RGB Output RangeEffective when connected to a device that only supportsRGB output.Standard: The video is output as it is.Enhanced: When the black and white contrast of a video is low, the signalis enhanced to reproduce clear video.HDMI Audio OutputThis setting selects whether or not to output audio fromHDMI.On:Off: When the TV is connected to this unit using an HDMI cable, and this unitis also connected to other devices, such as an amplifier/receiver using anoptical digital audio cable or a coaxial cable.VIERA LinkSet to use “HDAVI Control” function when connected withan HDMI cable to a device that supports “HDAVI Control”.On:Off: Select when you do not want to use “HDAVI Control”.Component Video ResolutionThis sets the video output resolution when using thecomponent video terminal.480i 480p 720p 1080iEven if you select “720p” or “1080i”, the video output resolution is restricted to“480p” when images of DVD-Video discs are output from the COMPONENTVIDEO OUT terminals.SpeakerYou can set the unit to output the best possible sound foryour speakers.Multi Channel: When using 3 or more speakers. ( 29)2 Channel: When using two speakers.2ch down-mix audio are output from Front L and Front R.“Network”IP Address/DNS Settings ( 12)Press [OK] to show the following settings.Connection Test — — — —IP Address Auto Configuration (DHCP) On OffIP Address — — —. — — —. — — —. — — —Subnet Mask — — —. — — —. — — —. — — —Default Gateway — — —. — — —. — — —. — — —DNS Auto Configuration (DHCP) On OffPrimary DNS — — —. — — —. — — —. — — —Secondary DNS — — —. — — —. — — —. — — —Auto Detect Connection Speed On OffConnection Speed SettingThis is enabled only when “Auto Detect Connection Speed” isturned “Off”.10BASE Half Duplex 10BASE Full Duplex100BASE Half Duplex 100BASE Full DuplexProxy Server Settings ( 13)Press [OK] to show the following settings.Reset to factory presetProxy Address (The initial setting is blank.)Proxy Port Number (The initial setting is “0”.)