Panasonic DMP-BD50 Operating Instructions Manual

Also see for DMP-BD50: Operating instructions Operating instructions

Contents

34RQT9184(ENG)MessagesThe following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup anduse.On the television PageAuthorization ErrorThis unit is not authorized toplay this title.You are trying to play the DivX VOD content that was purchased with a differentregistration code. You cannot play the content on this unit. 20Cannot play. You inserted an incompatible disc (Discs recorded in PAL video, etc.). 4, 5Cannot display on this unit. You tried to play a non-compatible image.Confirm “SD” on the unit’s display is not blinking and re-insert the card.5, 22—No disc is inserted. The disc may be upside down. —Rental Expired. The DivX VOD content has zero remaining plays. You cannot play it. 20This operation is currentlydisabled.The operation is prohibited by the unit or disc. —Cannot connect.Please check the connection ofthe LAN cable.When a hub is used but its Link lamp does not light up, check the cable connection, LANterminal connection, cable itself (a cross cable may be used by mistake), etc. 9IP address is not set. The “IP Address” in “IP Address/DNS Settings” is “---. ---. ---. ---“. Set the “IP Address”,“Subnet Mask”, and “Default Gateway“. (Select the automatic address acquisition ifnecessary.)12Cannot obtain IP address usingDHCP.Please check the connection orrouter settings.If you use a hub, then check the connection between the hub and the router.– Use the UPLINK port of the hub to connect to a router.– Check whether or not the hub’s Link lamp lights up. If it does not light up, then check thecable connection, LAN terminal connection, cable itself (a cross cable may be used bymistake), etc.If the above conditions are OK, then the router may not operate in DHCP mode. Check therouter settings and operation. You may reset the router to restore it to normal.9This IP address is already inuse.Please check the IP addresssetting.This unit’s IP address is used by another device. Check the IP addresses of this unit,personal computers, and routers, etc. If necessary, reconfigure them to avoid IP addressesfrom being duplicated. —Unable to perform ConnectionTest.Please try again.Turn the unit off. Remove the power cord and reconnect it and try again. If the samesymptom persists, then consult your dealer. —IP address not set correctly.Connection Test wasunsuccessful. No replyfrom host.Please check the connection orrouter settings.If you use a hub, then check the connection between the hub and the router.– Use the UPLINK port of the hub to connect to a router.– If the hub’s Link lamp does not light up, then check the cable connection, LAN terminalconnection, cable itself (a cross cable may be used by mistake), etc.Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP Address/DNSSettings”.If the MAC address information is required, then press [SETUP] to display the “Network”menu.91212Network connection refused.Please confirm Setup “BD-LiveInternet Access”When you set “BD-Live Internet Access” to “Allow (Limited)” and play BD-Live contentswhich do not have a content owner certificate, the Internet access of the content is notallowed. If you allow the content to connect to Internet, set “BD-Live Internet Access” to“Allow (ALL)”.26On the unit’s displayF99 The unit fails to operate properly. Press [POWER /I] on the main unit to switch the unit tostandby for 3 seconds. Now press [POWER /I] on the main unit again to turn the unit on.—HDMI ONLY Some BD-Video discs can only be output with HDMI. —No PLAY There is a viewing restriction on a BD-Video or DVD-Video. 26No READ The disc is dirty or badly scratched. The unit cannot play. —PLEASE WAIT Displayed when the unit is started and turned off. This is not a malfunction.The unit is carrying out its recovery process. You cannot operate the unit while “PLEASEWAIT” is displayed.——SET(“ ” stands for a number.)The remote control and main unit are using different codes. Change the code on theremote control.Press and hold [OK] and the indicated number button at the sametime for more than 5 seconds.33UNFORMAT You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL orDVD-RW (DVD-Video format).—UNSUPPORT You have inserted a disc the unit cannot play. 4, 5U59 The unit is hot.The unit switches to standby for safety reasons. Wait for about 30 minutes until themessage disappears.Select a position with good ventilation when installing the unit. Do not block the cooling fanon the rear of the unit.—U72U73The HDMI connection acts unusually.– The connected equipment is not HDMI compatible.– Please use HDMI cables that have the HDMI logo (as shown on the cover).– The HDMI cable is damaged.—