Panasonic DMR E50 Operating Instructions Manual

Also see for Diga DMR-E50: Operating instructions Operating instructions Operating instructions

Contents

34Timer recording (continued)Manual programming[RAM] [DVD-R]Remote control onlyYou can set your own programming conditions (up to 16programmes).Preparation≥Switch [DVD, TV] (15) to “DVD”.≥Ensure that this unit’s clock is set correctly.≥Insert a disc for recording (make sure there is enough room forthe programme you are going to record plus a little extra).1 Press [PROG/CHECK] (13).≥The Timer Programme List screen appears.A line that is ready for programming is highlighted.2 Press [ENTER] (10).≥The Timer Programme Correction screen appears.3 Use [1] (10) to move through the items and changethe items with [3, 4] (10).≥The current settings are shown each time you press [1](10).≥You may use the numeric buttons (4) to enter “Name”,“Date”, “Start” and “Stop”.≥Name (Programme Position/TV Station Name)≥DateCurrent date>the day before one month later>Daily (Sunday to Saturday)>Daily (Monday to Saturday)>Daily (Monday to Friday)>Weekly (Sundays)>...>Weekly (Saturdays)≥Start (start time)/Stop (finish time)The time increases or decreases in 30-minute increments ifyou hold the button.≥Mode (Recording mode)XP>SP>LP>EP>FR (page 26)≥PDCON>OFF (jjj) (page 33)≥TitleSelect “Title” and press [ENTER] (10), then refer to page 37for entering title.4 Press [ENTER] (10) when you have finished makingchanges.≥To continue programming:Repeat steps 2, 3, and 4.5 Press [PROG/CHECK] (13) or [RETURN] (23).To put the unit on recording standbyPress [ , TIMER] (12).Ensure “ ” lights on the unit’s display.To change the timer recording programme1) While the Timer Programme List Screen is being shown, use[3, 4] (10) to select the programme you want to change, andpress [ENTER] (10) to show the Timer Programme Correctionscreen.≥You may also select programme by inputting a 2-digit numberusing the numeric buttons (4).≥Use [2, 1] (10) to move to the page preceding or followingthe one on display.2) Move through the items with [1] (10) and change the settingswith [3, 4] (10) and press [ENTER] (10).Note≥The built-in clock employs 24-hour system.≥The remaining time is not shown if you insert discs other thanDVD-RAM or DVD-R.≥The remaining time displayed is calculated based on the currentrecording mode.≥If the disc is protected (pages 38, 73), the unit switches tostandby but does not go on standby for recording. Check the disccarefully.≥Recording is not possible unless you set “Disc Protection” in“DISC INFORMATION” to “Off” (page 38).≥You cannot record to a disc if the write protect tab on a cartridgedisc is set to protect. Release this before operation (page 73).≥Even if the unit is put in the timer recording standby mode or thetimer recording is being performed, you can play a programme.≥If the unit is not put in the timer recording standby mode at thelatest 10 minutes before the programmed timer recording startingtime, the [ ] flashes on the unit display. In this case, press the[ , TIMER] (12) button to put the unit in the timer recordingstandby mode.≥When recording more than one programme in a row, for DVD-RAM the first few seconds, and for DVD-R about the first 30seconds of all programmes from the second one onwards will notbe recorded.RETURNSELECTSP OK1:221:19BBC 1 16/ 7 TUE01Mode DiscspaceStopStartNo. Name Date1:58 SPTIMERRECORDING Remain1:19:00 16.7 TUEENTERNew Timer ProgrammeOFFPDCPress ENTER to storenew programme.RETURNNo.SELECT1:58 SPTIMERRECORDING Remain1:55:00 16.7 TUEENTER--0 9--:-- ------------ModeStopStartName Date--:-- -- SP----PDCPlease set Channel.---Title1:58 SPTIMERRECORDING Remain1:19:00 16.7 TUE2:0016/ 7 TUEModeStopStartName DateSPBBC 1 1:00PDCOFFTitle