Panasonic DMR-XS350 Operating Instructions Manual

Also see for DMR-XS350: Help guide

Contents

90RQT9439Changing the unit’s settings(All factory default settings are indicated with underlined text.)Component ResolutionThis sets the video output resolution when using the componentvideo terminal.[576i/480i] [576p/480p] [720p] [1080i]≥You cannot change the setting while the “HDMI Video Mode” isset to “On”. Set the “HDMI Video Mode” to “Off” and set the “AV1Output” to “Video ( with component )” or “S Video ( withcomponent )”.≥If it is set to “720p”, images other than “720p” will be output as“1080i”.≥The video output resolution will be restricted to “576p/480p” evenif you select “720p” or “1080i” when viewing or recording thefollowing images:– Some programmes in the HD format– DVD-Video discs– DivX– Images input via AV1, AV2 or DV input≥Press the [∫] and [1] (PLAY) for more than 5 seconds when theimage is disturbed by changing the setting. It will be set to “576i/480i”.AV1 OutputSet according to the terminal of the connected TV.Select “Video ( with component )” or “S Video ( with component )”for component output (progressive output).If this unit is connected with an HDMI cable, you cannot select“RGB 1 ( without component )” or “RGB 2 ( without component )”.When a decoder is connected, do not set to “RGB 1 ( withoutcomponent )”.[Video ( with component )]Select when a TV is connected that can receive a composite signal.[S Video ( with component )]Select when a TV is connected that can receive an S Videosignal.[RGB 1 ( without component )]Select when a TV is connected that can receive an RGB signal. Ifyou always would like to view the picture from the unit in RGBsignal, select this mode. The TV screen will automatically switchto display the picture from the unit when the unit is turned on.[RGB 2 ( without component )]Select when a TV is connected that can receive an RGB signal. Ifyou would like to switch to display the picture from the unit onlywhen playback or viewing menus, select this mode.AV2 SettingsSet to match the connected equipment.≥Press [OK] to show the following settings.AV2 InputSet to “RGB / Video” or “RGB” when receiving or recording RGBoutput from external equipment.[RGB / Video] [RGB] [Video] [S Video]Ext LinkThis setting cannot be made when the “TV System” is set to“NTSC” (> 89).[Ext Link 1] When a Set Top Box etc. which transmits a specialcontrol signal recordings via the 21-pin Scart cableis connected.Start and stop timings of recording are controlledby the control signal.[Ext Link 2] When external equipment with a timer function isconnected.When it turns on, recording starts.When it turns off, recording stops.Common InterfaceAccess to software contained on Common Interface (CI) modules.(> 16, 19) Follow the on-screen instructions.Network SettingsIP Address / DNS Settings (> 92 )≥Press [OK] to show the following settings.Connection TestIP Address Auto-assignment[On] [Off]IP AddressSubnet MaskGateway AddressDNS-IP Auto-assignment[On] [Off]Primary DNSSecondary DNSConnection Speed Auto-configure[On] [Off]Connection Speed SettingThis is enabled only when “Connection Speed Auto-configure” isturned “Off”.[10BASE half duplex] [10BASE full duplex][100BASE half duplex] [100BASE full duplex]Proxy Server Settings (> 93 )≥Press [OK] to show the following settings.InitializeSet the setting of the “Proxy Server Settings” back.Proxy Address(The initial setting is blank.)Proxy Port Number(The initial setting is “0”.)Connection TestInternet Content Settings (> 93)≥Press [OK] to show the following settings.LockYou can restrict using VIERA CAST.Follow the on-screen instructions. Enter a 4-digit PIN with thenumbered buttons when the PIN setting screen is shown. It will bethe common PIN for “DVD-Video Ratings” and “Lock”.Do not forget your PIN.[On] [Off]Automatic Volume Control[On][Off] Select “Off” when the audio is warped whileusing VIERA CAST.Home Network ( DLNA ) Settings (> 93)You will be able to access this unit from Panasonic DLNAcompatible equipment on the network by registering them to thisunit.It is also possible to change the name of this unit on the network.Server ( DLNA ) Settings (> 93)By allowing access from non-Panasonic DLNA compatibleequipment on the network, it allows them to access this unit.